![](/images/new-backgrounds/1130008/13000873x1.webp)
If your cable box has its own remote to change channels, you will
probably be able to program the TV's remote to control both the TV and
the cable box.
The TV's remote is designed to control several brands of cable
boxes. To program the remote, just press CABLE, then ID, then the two-
digit code number for your brand of cable box. Refer to the chart below
to find the code number for your cable box. Press the OFF/ON button next to confirm operation.
You may need to try each of the code numbers listed for your brand until you find the one that works.
After the TV's remote is programmed, you'll be able to turn on the cable box by pressing CABLE,
then OFF/ON. You can change channels on the cable box by
pressing the CHANNEL buttons whenever the remote is in the "cable"
mode. To put the remote in the "cable" mode, press the CABLE
button. Press the TV button to put the remote back into the TV mode so
the remote buttons will control the TV again.
Programming Remote To Control
1.Refer to the chart below to find the code number that corresponds to the brand name of your cable box. Keep this number in mind. If more than one number is listed, you may need to try each one separately until you find the one that works.
2.Press CABLE button on remote.
3.Press 11) button on remote.
4.Press two number buttons (first one, then the other) to enter the code number for your brand of cable box. Note: You must press the two number
buttons within three seconds of pressing the ID button.
Cable Box
5.Point the remote at the cable box and
press the OFF/ON button to test the code number.
•If the right number was entered, the cable box should turn on. Pressing the CHANNEL buttons should then also change channels on the
cable box.
•If the cable box does not react to
the remote (or if the remote turns on the cable box but does not
change channels), repeat steps 1 thru 5 with another code number.
Operating Notes:
•After the remote is programmed, it will turn on the cable box whenever you press CABLE and then OFF/ON.
•To turn off the cable box, press CABLE, then OFF/ON.
•To change channels on the cable box,
press CABLE then CHANNEL up or down.
•You may have to reprogram the remote control if you change its batteries. Try
not to press any buttons while changing batteries.
Anvision | ..................................................................................... | 07,08 |
Cablestar | 07,08 | |
Eagle | 08 | |
Eastern | International | ........... 02 |
General | Instrument | 04,05,15,23,24,25,30,36 |
Hamlin | 12,13,34 | |
Hitachi | 37,43 | |
Jerrold | .04,05,15,23,24,25,30,36 | |
MACOM | _...... 37,43 | |
Magnavox | 07,08,19,26,28,29,32,33,40,41 | |
NSC | 09 | |
Oak | 01,16,38 | |
Oak Sigma | 16 | |
Panasonic | 27,39 |
Philips | 07,08,19,26,28,29,32,33,40,41 | |
Pioneer | 18,20 | |
Randtek | . ............................. | 07,08 |
RCA | 27 | |
Regal | 12,13 | |
Regency | 02 | |
Scientific Atlanta | 03,22 | |
Sylvania | ........................................................................... | 11 |
Teknika | 06 | |
Texscan | 10,11 | |
Tocom | 17,21 | |
Unika | 31 | |
Viewstar | 07,08,19,26,28,29,32,33,40,41 | |
Zenith | 14,42 |
Note: Refer to the information sheet packed with your remote control for the latest list of brand names and code numbers. Because this list is constantly growing, the information sheet packed with your remote control may be a later version of this list and contain additional brands and/or code numbers.
35