INSTALLATION

IMPORTANT:

SAVE THESE

INSTRUCTIONS

The Regency Gas Fireplace must be installed in accordance with these instructions. Carefully read all the instructions in this manual fi rst. Consult the "authority having jurisdiction" to determine the need for a permit prior to start- ing the installation. It is the responsibility of the installer to ensure this fi replace is installed in compliance with the manufacturer's instructions and all applicable codes.

BEFORE YOU START

Safe installation and operation of this appli- ance requires common sense, however, we are required by the Canadian Safety Standards and ANSI Standards to make you aware of the following:

INSTALLATION AND REPAIR SHOULD BE DONE BY A QUALIFIED SERVICE PERSON. THE APPLIANCE SHOULD BE INSPECTED BEFORE USE AND AT LEAST ANNUALLY BY A PROFESSIONAL SERVICE PERSON. MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING,BEDDINGMATERIAL, ETC. IT IS IMPERATIVE THAT CONTROL COMPARTMENTS, BURNERS AND CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS APPLIANCE CORRECTLY WILLVOIDYOURWARRANTYAND MAY CAUSE A SERIOUS HOUSE FIRE.

CHILDRENANDADULTS SHOULD BEALERTEDTOTHEHAZARDSOF HIGH SURFACE TEMPERATURES, ESPECIALLY THE FIREPLACE GLASS,AND SHOULD STAYAWAY TO AVOID BURNS OR CLOTHING IGNITION.

YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.

C L O T H I N G O R O T H E R FLAMMABLE MATERIALSHOULD NOT BE PLACED ON OR NEAR THE APPLIANCE.

GENERAL SAFETY INFORMATION

1)The appliance installation must conform with local codes or, in the absence of local codes, with the current Canadian or National Gas Codes, CAN1-B149 or ANSI Z223.1 Installation Codes.

2)The appliance when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the current National Electrical Code, ANSI/NFPA 70 or CSA C22.1 Canadian Electrical Code.

3)See general construction and assembly instructions. The appliance and vent should be enclosed.

4)This appliance must be connected to the specifi ed vent and termination cap to the outside of the building envelope. Never vent to another room or inside a building. Make sure that the vent is installed as per Venting instructions.

5)This appliance may only be installed in a vented, solid fuel burning masonry, listed factory built fi replace, or zero clearance kit part # 530-936.

6)This appliance is Listed for bedroom installations when used with a Listed Millivolt Thermostat. Some areas may have further requirements, check local codes before installation.

7)This appliance is Listed for Alcove installations, maintain minimum Alcove clearances as follows, minimum ceiling height of 53-1/2", minimum width of 48" and a maximum depth of 36".

8)This unit is not approved for installation into a mobile home.

9)Inspect the venting system annually for blockage and any signs of deterioration.

10)Any safety glass removed for servicing must be replaced prior to operating the appliance.

11)To prevent injury, do not allow anyone who is unfamiliar with the operation to use the fi replace insert

12)Wear gloves and safety glasses for protection while doing required maintenance.

13)Ensure adequate combustion and ventilation air.

14)Under no circumstances should this appliance be modifi ed. Parts that have to be removed for servicing should be replaced prior to operating this appliance.

15)Installation and any repairs to this appliance should be done by a qualifi ed service person. A professional service person should be called to inspect this appliance annually. Make it a practice to have all of your gas appliances checked annually.

16)Do not slam shut or strike the glass door.

17)Under no circumstances should any solid fuels (wood, paper, cardboard, coal, etc.) be used in this appliance.

18)The appliance area must be kept clear and free of combustible materials, (gases and other fl ammable vapours and liquids).

19)Do not use this appliance if any part has been under water. Immediately call a qualifi ed service technician to inspect the appliance and to replace any part of the electrical control system and any gas control which has been under water.

20)WARNING: Failure to position the parts in accordance with the diagrams in this manual or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

21)WARNING: Operation of this appliance when not connected to a properly installed and maintained venting system or tampering with the blocked vent shut-off system can result in carbon monoxide (CO) poisoning and possible death.

Emissions from burning wood or gas could contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

Regency E21 Gas Fireplace Insert

5

Page 5
Image 5
Regency E21-NG1, E21-LP1 installation manual Installation, Save These Instructions, Before YOU Start

E21-NG1, E21-LP1 specifications

The Regency E21-LP1 and E21-NG1 are premium gas fireplaces that embody the essence of modern heating technology while offering unparalleled aesthetic appeal. Designed to meet the demands of today’s homeowners, these models combine efficiency, style, and innovative features to elevate any living space.

One of the standout characteristics of the E21 series is its sleek design, which integrates seamlessly into a variety of home decors. Both the E21-LP1 and E21-NG1 are designed for liquid propane and natural gas respectively, ensuring versatility in fuel options. Their clean lines and minimalist profile make them an attractive focal point, perfect for modern, contemporary, or transitional interiors.

These gas fireplaces feature advanced heating technology, providing robust warmth quickly and efficiently. The E21 models are equipped with an impressive direct vent system that ensures optimal performance while maintaining indoor air quality. This means that the fireplace pulls air from the outside for combustion and vents exhaust back outside, allowing for ventilation without compromising on comfort.

Energy efficiency is a key characteristic of the Regency E21 models. They boast a high efficiency rating, which translates into lower heating costs and reduced environmental impact. The innovative burner design enhances flame presentation, providing a realistic and inviting fire that enhances the ambiance of any room.

Ease of use is also a significant benefit of the E21-LP1 and E21-NG1. With an intuitive control panel, users can easily manage the flame height and adjust the heat output to suit their needs. Many homeowners appreciate the convenience of remote control operation, allowing them to adjust their fireplace settings from the comfort of their seat.

Safety features are paramount in the design of the E21 models. Each fireplace is equipped with standard safety mechanisms, including an automatic shut-off system that activates in the event of a malfunction. This provides peace of mind for users, ensuring that their heating source is both effective and secure.

In summary, the Regency E21-LP1 and E21-NG1 offer a blend of modern design, advanced technology, and high efficiency, making them ideal choices for anyone looking to invest in a reliable and stylish gas fireplace. With an emphasis on user-friendly features and safety, they promise to deliver warmth and comfort for years to come.