Regency F38-LPG2 Copy of the Lighting Plate Instructions, For Your Safety Read Before Lighting

OPERATING INSTRUCTIONS

COPY OF THE LIGHTING PLATE INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or Natural Gas and Propane Installation Codes, CSA B149.1. (Australia: AS5601-2004, New Zealand: NZS 5261)

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or gas supplier.

A) This appliance has a pilot which must be lighted	a qualified service technician. Force or attempted
by hand, following the instructions below	repair may result in a fire or explosion.
exactly.	D) Do not use this appliance if any part has been under
B) BEFORE LIGHTING smell all around the appliance	water. Immediately call a qualified service techni-
area for gas. Be sure to smell next to the floor	cian to inspect the appliance and to replace any part
because some gas is heavier than air and will	of the control system and any gas control which has
settle on the floor.	been under water.
WHAT TO DO IF YOU SMELL GAS	This appliance needs fresh air for safe operation and
- Do not try to light any appliance	must be installed so there are provisions for adequate
- Do not touch any electric switch, do not use any	combustion and ventilation air.
phone in your building	CAUTION: Hot while in operation. Do not touch.
- Immediately call your gas supplier from a
neighbors phone. Follow the gas supplier’s in-	Severe Burns may result. Due to high surface
structions.	temperatures keep children, clothing and
- If you cannot reach your gas supplier, call the	furniture, gasoline and other liquids having
fire department.	fammablevaporsaway.Keepburnerandcontrol

C)Use only your hand to push in or turn the gas compartment clean. See installation and

control knob. Never use tools. If the knob will not operatinginstructionsaccompanyingappliance.

push in or turn by hand, don’t try to repair it, call

LIGHTING INSTRUCTIONS

STOP! Read the safety information above on this				Release knob and it will pop back up. Pilot should
label.				remain lit. If it goes out, repeat steps 3) and 4).
1) Push in gas control knob slightly and turn				If knob does not pop up when released, stop and
clockwise	to “OFF”. Knob cannot be turned			immediately call your service technician or gas
from “PILOT” to “OFF” unless knob is pushed in				supplier.
slightly. Do	not	force.		If the pilot will not stay lit after several tries, turn the
2) Wait five (5) minutes to clear out any gas. If you				gas control knob to “OFF” and call your service
then smell gas STOP! follow “B” in the safety				technician or gas supplier.
information above on this label. If you don’t smell				5) Turn gas control knob counterclockwise		to “ON”.
gas, go to the next step.				6) Use rocker switch to operate main burner.
3) Turn knob	on	gas control	counterclockwise	PILOT BURNER
to “PILOT”.				VEILLEUSE			OFF
4) Push in control		knob all the	way and hold in.	THERMOPILE
Immediately push black button on spark igniter				ELEMENT	Gas Inlet
until pilot	lights. Continue to		hold the control
				THERMO-
knob in for about 1/2 minute after the pilot is lit.				ELECTRIQUE

TO TURN OFF GAS APPLIANCE

1) Push in the gas control knob slightly and turn

clockwise to “OFF”. Do not force.

2)Turn off all electric power to the appliance if service is to be performed.

You may shut off the pilot during prolonged non use periods to conserve fuel.

DO NOT REMOVE THIS INSTRUCTION PLATE 908-649c

WARNING:

DO NOT SPRAY AEROSOLS IN THE VICINITY OF

THIS APPLIANCE WHILE IN OPERATION.

Regency F38-2 Freestanding Gas Heater 15