INSTALLATION

IMPORTANT:

SAVE THESE

INSTRUCTIONS

The Regency P121/P121LC/P121RC/P131-NG or P121/P121LC/P121RC/P131-LPG Room Sealed Gas Fireplace must be installed in ac- cordance AG601 and NZS 5261 and with these instructions. Carefully read all the instructions in this manual first. Consult the "authority having jurisdiction" to determine the need for a permit prior to starting the installation. It is the respon- sibility of the installer to ensure this fireplace is installed in compliance with manufacturer's instructions and all applicable codes.

BEFORE YOU START

Safe installation and operation of this appliance requires common sense, however, we are required to make you aware of the following:

INSTALLATIONANDREPAIRSHOULD BEDONEBYAAUTHORIZEDSERVICE PERSON.THEAPPLIANCESHOULDBE INSPECTED BEFORE USE AND AT LEASTANNUALLYBYAAUTHORIZED SERVICEPERSON.MOREFREQUENT CLEANINGMAYBEREQUIREDDUETO EXCESSIVE LINT FROM CARPETING, BEDDINGMATERIAL,ETC.ITISIMPER- ATIVE THAT CONTROL COMPART- MENTS,BURNERSANDCIRCULATING AIR PASSAGEWAYS OF THE APPLI- ANCEBEKEPTCLEAN.

DUE TO HIGH TEMPERATURES, THE APPLIANCESHOULDBELOCATEDOUT OFTRAFFICANDAWAYFROMFURNI- TUREANDDRAPERIES.

WARNING:FAILURETOINSTALLTHIS APPLIANCE CORRECTLY WILL VOID YOURWARRANTYANDMAYCAUSEA SERIOUSHOUSEFIRE.

CLOTHINGOROTHERFLAMMABLEMA- TERIAL SHOULD NOT BE PLACED ON ORNEARTHEAPPLIANCE.

CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACETEMPERATURES,ESPECIAL- LY THE FIREPLACE GLASS, AND SHOULDSTAYAWAYTOAVOIDBURNS ORCLOTHINGIGNITION.

YOUNG CHILDREN SHOULD BE

CAREFULLY SUPERVISEDWHENTHEY ARE IN THE SAME ROOM AS THE AP- PLIANCE.

GENERAL SAFETY

INFORMATION

1)The appliance shall be installed in accord- ance with the manufacturer's installation instructions, local gas fitting regulations, municipal building codes, water supply reg- ulations, electrical wiring regulations, with AS5601-2004 (AGA gas installation code) NZS 5261 (New Zealand)

2)See general construction and assembly instructions. The appliance and flue should be enclosed.

3)This appliance must be connected to the specified flue and termination cap to the outside of the building envelope. Never flue to another room or inside a building. Make sure that the flue is fitted as per Flueing instructions.

4)Inspect the flueing system annually for blockage and any signs of deterioration.

5)Flueing terminals shall not be recessed into a wall or siding.

6)Any safety glass removed for servicing must be replaced prior to operating the appliance.

7)To prevent injury, do not allow anyone who is unfamiliar with the operation to use the fireplace.

8)Wear gloves and safety glasses for pro- tection while doing required maintenance.

9)Be aware of electrical wiring locations in walls and ceilings when cutting holes for termination.

10)Under no circumstances should this appli- ance be modified. Parts that have to be removed for servicing should be replaced prior to operating this appliance.

11)Installation and any repairs to this appliance should be done by a authorized service person. A authorized service person should be called to inspect this appliance annually. Make it a practice to have all of your gas appliances checked annually.

12)Do not slam shut or strike the glass door.

13)Under no circumstances should any solid fuels (wood, paper, cardboard, coal, etc.) be used in this appliance.

14)The appliance area must be kept clear and free of combustible materials, (gases and other flammable vapours and liquids).

Emissions from burning wood or gas could contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

INSTALLATION

CHECKLIST

Note: These units are

non-load bearing.

1)Locate appliance

a)Room location, page 8.

b)Clearances to Combustibles, page 9.

c)Mantle Clearances, page 9.

d)Framing & Finishing Requirements, page 10.

e)Flueing Requirements, pages 11-19.

2)Assemble Top Standoffs, page (NOTE: page 11 must be done before installing unit into fireplace.)

3)Install flue, pages 19-21.

4)Make gas connections. Test the pilot. Must be as per diagram. Page 22.

5)Install log set where indicated on page 24-25.

6)Glass Door Removal (page 26), Louvers or Grills (page 26), and Finishing Trim (page 26).

7)Install optional Wall Switch, Remote Con- trol, or Wall Thermostat, page 27.

8)Final check.

Before leaving this unit with the customer, the installer must ensure that the appliance is firing correctly and operation fully explained to cus- tomer.

This includes:

1)Clocking the appliance to ensure the cor- rect firing rate (rate noted on label 40,000 Btu/h NG, and 39,000 Btu/h LPG) after burning appliance for 15 minutes.

2)If required, adjusting the primary air to ensure that the flame does not carbon. First allow the unit to burn for 15-20 min. to stabilize.

CAUTION: Any alteration to the product that causes sooting or carboning that results in damage is not the responsi- bility of the manufacturer.

Regency P121/P121LC/P121RC/P131 Zero Clearance Room Sealed Gas Fireplace

5

Page 4 Page 6
Page 5
Image 5
Regency P121LC-NG, P131-NG, P121RC-NG Installation, Save These Instructions, Before YOU Start, General Safety Information
Page 4 Page 6

P121RC-NG, P131-NG, P121LC-NG, P121-NG specifications

The Regency P131-NG, P121LC-NG, P121RC-NG, and P121-NG are a series of advanced communication devices designed to set new standards in the realm of radio technology, especially for industrial and commercial applications. These devices are engineered to provide reliable performance, exceptional clarity, and robust features that cater to the diverse needs of users in various sectors.

One of the standout features of the Regency P131-NG and its counterparts is their enhanced communication range. Utilizing advanced digital signal processing technology, these radios ensure clear audio transmission even in challenging environments. This capability is crucial for users operating in areas with significant interference or in remote locations, where traditional radios may fail to maintain a stable connection.

The devices also boast a rugged design, tailored for durability and resistance to environmental factors. With an IP67 rating, the P131-NG series is protected against dust and can withstand immersion in water, making it ideal for outdoor use. The robust build quality ensures that these radios can endure the rigors of everyday use in industrial settings.

In terms of user interface, the P121LC-NG and P121RC-NG are equipped with intuitive controls that facilitate ease of use. The large display screen offers clear visibility of channel information and battery status, while the customizable buttons allow users to quickly access their most-used functions. Additionally, these models feature programmable channels, enabling users to tailor their communication needs effectively.

Battery life is another key characteristic of these radios. The devices are designed with energy efficiency in mind, offering extended use between charges. This is complemented by rapid charging technology, which ensures that downtime is minimized, allowing users to stay connected when it matters most.

Additionally, the inclusion of advanced security features is noteworthy. The P131-NG series incorporates encryption capabilities that safeguard sensitive communications, making them an excellent choice for organizations concerned about data security.

Overall, the Regency P131-NG, P121LC-NG, P121RC-NG, and P121-NG stand out in the crowded market of communication devices by offering a combination of superior range, robust construction, user-friendly interfaces, long battery life, and enhanced security features. These radios are poised to meet the demands of a wide array of users, from industrial workers to commercial enterprises, providing reliable communication solutions in any environment.
Top Page Image Contents