MAINTENANCE
CAUTION: Never leave unit unat- tended if door is left open. This procedure is for fire
3)With the draft still in the fully open position add two or three seasoned logs to your fi re. Form a trench in the ash bed to allow air to reach the rear of the fi rebox prior to closing the door.
4)During the first few days it may be more difficult to start the fire. As you dry out your firebrick, your draft will increase. Due to the large quantity of firebrick, which has a high water content, it may take many
fires (20 or more) to thoroughly cure the
firebrick. The fi rebrick will become lighter in colour as it dries out.
5)After about 15 to 20 minutes, when your wood has begun to burn strongly, adjust your draft control down to keep the fi re at a moderate level.
WARNING: Never build a roaring fire in a cold stove. Always warm your stove up slowly!
6)Once a bed of coals has been established, you may adjust the draft control to a low set- ting to operate the unit at its most effi cient mode.
7)For the first few days, the stove will give off an odour from the paint and oil burn off. This is to be expected as the high temperature paint becomes seasoned. Windows and/or doors should be left open to provide adequate ventilation while this temporary condition exists. Burning the stove at a very high temperature the fi rst few times may damage the paint. Burn fi res at a moderate level the
first few days.
8)For those units installed at higher elevations drafting problems may occur. Consult an experienceddealeronmethodsofincreasing your draft (refer to the Flue Height Chart).
9)Some cracking and popping noises may be experienced during the heating up process. These noises will be minimal when your unit reaches temperature.
10)Before opening your door to reload, open draft fully for approximately 10 to 15 seconds until fi re has been
11)All fuel burning appliances consume oxygen during operation. It is important that you supply a source of fresh air to your unit while burning.
12)Green or wet wood is not recommended for your unit since most of the energy will be used to drive off the moisture instead of heating your home. As well, green or wet wood can result in dirty glass.
13)Always maintain clean glass. Clean glass means a clean fl ue; if you are experiencing dirty glass you may be operating a fi re that is set too low. Ask your dealer for details.
14)Keep your spark arrester on the flue clean. It shouldbecheckedandmaintainedregularly, at least monthly.
SAFETY GUIDELINES
1)Never use gasoline, gasoline type lantern fuels, kerosene, charcoal lighter fuel or similar liquids to start or ‘freshen up’ a fire in your fi replace. Keep all such liquids well away from the unit while in use.
2)Keep the door closed during operation and maintain all seals in good condition.
3)Do not burn large quantities of paper in your fi replace.
4)If you have smoke detectors, prevent smoke spillage as this may set off a false alarm.
5)Do not overfi re fi replace. If overfi ring takes place, stop adding fuel and close the draft
control. Overfi ring can cause extensive damage to your unit including warpage and premature steel corrosion. Overfiring will void your warranty.
6)Do not permit creosote or soot
7)The fi replace face can be very hot. You may be seriously burned if you touch the unit while in operation. Warn children of the burn hazard.
8)Do not connect this unit to a chimney fl ue serving another appliance.
9)Do not use grates or andirons or other methods for supporting fuel. Burn directly on the bricks.
10)Whenrefuellingthefireturnoffblowers,open draft prior to slowly opening the door. Failure to do so could result in smoke spillage.
11)Your unit should burn dry, standard firewood only. Theuse of“millends”isdiscouragedas this fuel can easily overheat your fi replace. Evidence of excessive overheating will void your warranty.
As well, a large portion of sawmill waste is chemically treated lumber, which is illegal
to burn in many areas. Salt drift wood, chemically treated fi re logs and pressure treated woods must not be burned in your woodstoves.
12)Do not store any fuel closer than 2 feet from your unit.
13)IMPORTANT: Do not obstruct the convec- tion louvers at any time. Blocking air into this area will cause excessively high fi rebox temperatures and a potentially dangerous situation.
MAINTENANCE
Gold Plated Doors and Louvers
The optional gold electroplated fi nish on the doors and louvers requires little maintenance and needs only to be cleaned with a damp cloth. DO NOT use abrasive materials or chemical cleaners, as they may harm the fi nish and void the warranty. Keep doors and louvers off during construction to avoid damage.
Door Gasket
If the door gasket requires replacement, your must use 7/8 in. dia. oval, high density mate- rial,
Door Hinges
Grease door hinges with high temperature grease regularly for smooth operation and to avoid squeaks.
Glass Cleaning
Only clean your glass window when it is cool. Your local retailer can supply you with a recommended glass cleaner if plain water and a soft cloth does not remove all deposits. Do not use oven cleaner on the glass as it will etch the glass.
Glass Removal/Replacement
Allow the stove to cool before removing or replacing glass. Remove the door from the insert and remove the glass retainer. Use caution when removing broken glass to avoid injury. When placing the replacement glass in the door, make sure that the glass gasketing will properly seal your unit. Replace the retainer and tighten securely, but do not wrench down on the glass as this may cause breakage. Do not substitute materials. If your glass door breaks, do not use your unit until it has been replaced (refer to Glass Installation section).
20 | Regency Z2510 WarmHearth |
