INSTALLATION
READ BEFORE YOU INSTALL THE REGENCY WARMHEARTH HIGH EFFICIENCY EPA CERTIFIED FIREPLACE
This installation manual will enable you to make a safe, effi cient and dependable installation of your fi replace and chimney system. Please read and understand these instructions before beginning your installation.
Do not alter or modify the fi replace or its components under any circumstances. Any modification or alteration of the fireplace system, including but not limited to the fireplace, chimney components and accessories, may void the warranty, listing and approvals of this system and could result in an unsafe and potentially dangerous installation.
PLEASE RETAIN THIS MANUAL FOR
FUTURE REFERENCE.
IMPORTANT: Please read and follow these rules for safety.
1)Before starting your fi replace installation, read these installation instructions carefully to be sure you understand them in their entirety. Failure to follow them could cause a fi replace malfunction resulting in serious injury and/or property damage.
2)Always check your local building codes. The installation must comply with all local, regional and state codes and regulations.
3)This model fi replace must be installed with one of the chimney systems listed in the Chimney Section in this manual. These systems are intended for use as a residential type appliance. The chimney must always vent to the outside of the building.
4)To ensure a safe fi replace system and to prevent the
5)Use solid fuel only. DO NOTuse artificial logs containing petroleum products, chemical chimney cleaners, gas logs, gas lighters, salt contaminated wood or fl ame colorants in your fi replace. When using compressed sawdust logs use only at 1/3 capacity since these get very hot and expand.
6)DO NOT use charcoal or coal under any circumstances.
7)NEVER use gasoline,
8)NEVER leave children unattended when there is a fi re burning in the fi replace.
9)Allow the fi replace to cool before servicing. Always shut off any electricity to the fireplace while working on it. This will prevent any possible electrical shock.
10)Regency is not responsible for any smok- ing or related problems that may result from the lack of adequate combustion air. It is the responsibility of the installer to ensure that adequate combustion air has been provided for the fireplace.
11)Regency Industries Ltd. does not warranty “smoke free” operation nor are we respon- sible for inadequate system draft caused by mechanical systems, general construction conditions, inadequate chimney heights, adverse wind conditions and/or unusual environmental factors or conditions beyond our control.
12)DO NOT use a fi replace insert or any other product not specifi ed by Regency for use with this fi replace.
13)Never, under any circumstances, install a fi replace, chimney component or any ac- cessories, supplied by Regency, that have visible or suspected physical damage as a result of handling or transportation. These items should be inspected by a Regency dealer or qualifi ed factory representative to ensure safe condition. When in doubt, consult your Regency dealer.
14)It is recommended that power is supplied to the terminal block of the unit to allow for the installation of blower components now or at a future date.
Emissions from burning wood or gas could contain chemicals known to the State of Cali- fornia to cause cancer, birth defects or other reproductive harm.
DIMENSIONS AND SPECIFICATIONS
The WarmHearth is a woodburning fi replace featuring a
Note: Illustrations shown reflect “typical” installations with nominal dimen- sions and are for design and framing reference only. Actual installations may vary due to individual design preferences. However, always main- tain minimum clearances to combus- tible materials and do not violate any specific installation requirements.
The WarmHearth fi replace has been tested and listed by Warnock Hersey Inc. to UL. 127 Standard for U.S. installations and ULC. S610 standard for Canadian installations. This unit is intended for installation in conventional homes and buildings of conventional con- struction, not in mobile homes.
This fi replace system is designed for installation in accordance with the National Fire Protection Standard for chimneys, fi replaces and solid fuel burning appliances; NFPA 211 and in ac- cordance with codes such as the BOCA Basic National Codes, the Standard Mechanical Code, Uniform Building Codes, Canadian National Building Codes or applicable local codes.
Unit Dimensions
6 | Regency Z2510 WarmHearth |