OPERATING INSTRUCTIONS
OPERATING
INSTRUCTIONS
Beforeoperatingthisappliance,proceedthrough the following check list.
1)Read and understand these Instructions before operating this appliance.
2)Check to see that all wiring is correct and enclosed to prevent possible shock.
3)Check to ensure there are no gas leaks.
4)Make sure the three pieces of door glass are properly positioned. Never operate the appliance with any of the glass removed or with the door open.
5)Verify that all fl ueing and the cap is unob- structed.
6)Verify log placement. If the pilot cannot be seen when lighting the unit - the logs or the embers have been incorrectly positioned.
7)The unit should never to turned off and on without a minimum of a 60 second wait.
LIGHTING
INSTRUCTIONS
IMPORTANT: The PILOT knob cannot be
turned from pilot to off unless it is partially
depressed.
Note: Open the pedestal door of the unit before lighting the pilot. Once the pilot is lit, close the door. You should never operate the unit with the door open.
1)If the PILOT knob is in the off position proceed to Step 4.
Diagram 1
2)Push in PILOT knob slightly and turn clock- wise to off. Knob cannot be turned from pilot to off unless knob is pushed in slightly. Do not force.
3)Wait five minutes to allow gas, that may have accumulated in the main burner compart- ment, to escape. If you smell gas, follow the instructions on the front of this manual. If you don't smell gas continue on to the next step.
4)Turn the PILOT knob counterclockwise to pilot and align it with the arrow as shown in diagram 1.
5)Push in PILOT knob all the way in and hold. Immediately push IGNITOR button until pilot lights. Continue to hold the PILOT knob in for approximately one minute, then release the PILOT knob. The pilot fl ame should continue to burn. If the pilot does not remain lit, repeat operation allowing a longer period before releasing PILOT knob.
6)Turn PILOT knob counter clockwise to on.
7)Use the ON/OFF switch to turn on the burner.
8)Rotate the HEAT control to adjust the fl ame height higher or lower.
SHUTDOWN
INSTRUCTIONS
1)Use the ON/OFF switch, wall switch, thermostat or remote control to turn off the burner.
2)Push in the PILOT knob slightly and turn clockwise to off. Do not force.
3)Turn off all electric power to the appliance if service is to be performed.
FIRST FIRE
The FIRST FIRE in your heater is part of the paint curing process. To ensure that the paint is properly cured, it is recommended that you burn your fi replace for at least four (4) hours the fi rst time you use it with the fan on.
When fi rst operated, the unit will release an odour caused by the curing of the paint and the burning off of any oils remaining from manufac- turing. Smoke detectors in the house may go off at this time. Open a few windows to ventilate the room for a couple of hours. The glass may require cleaning.
DO NOT ATTEMPT TO CLEAN THE GLASS WHILE IT IS STILL HOT!
Note: When the glass is cold and the appli- ance is lit, it may cause condensation and fog the glass. This condensation is normal and will disappear in a few minutes as the glass heats up.
DO NOT BURN THE APPLIANCE WITHOUT THE GLASS FRONT IN PLACE.
DO NOT BURN THE APPLIANCE WITHOUT THE GLASS FRONT IN PLACE.
AUTOMATIC
CONVECTION
FAN OPERATION
Set the fan speed on control panel at the top rear of the unit to adjust to the desired speed. The fan will turn on as the stove comes up to operating temperature.Afterthe unit has been turned 
off and the unit cooled
to below a useful heat output range the fan will shut off automati- cally.
ADJUSTING FLAME
HEIGHT
Your heater has an adjustable fl ame to tailor the look and heat output to your specifi c needs. It is adjusted by turning the fl ame adjustment dial on the gas control valve.
Turn clockwise to adjust the fl ame higher, coun- terclockwise for a lower fl ame.
WARNING
DO NOT SPRAY AEROSOLS IN
THE VICINITY OF THIS
APPLIANCE WHILE IN
OPERATION
14 | Regency |
