INSTALLATION

be at the top so they lie flat. Bend out the lower edge of the valve at 4 places inside the fireplace with pliers so that it can't be pulled out again. Diagram 2.

Diagram 1

Diagram 2

5)Locate the blower in a convenient location near the fireplace. In a 2 story home one good location would be in the ceiling of the basement because you must be able to access it for oiling and replacement.

Note: The blower can be installed al- most anywhere in the home. How- ever, some thought should be put into the planning, to ensure blow- er noise is kept away from rooms that want quiet. Length of runs should be kept to a minimum to conserve space and minimize cost. Maximum duct length should normally not be more than 50 feet between the fireplace through the fan to the outlet farthest away. There is a loss of about 15% per- formance at 50 feet.

WARNING: The WarmHearth may be tied into your home's central warm air duct system by linking into the HOT air duct in any position you may choose, however, caution must be used to ensure that hot air produced by the WarmHearth can- not be drawn back into the central heating furnace.

6)Connect the inlet of the blower to the outlet of the valve using 8 inch diameter metal ducting (rigid or flex). Any other size will not work properly.

7)Duct-work can then be run to the desired rooms following good warm air distribution practices. Up to six 5 in. diameter runs can be installed from this system.

Note: The cross sectional area of the distribution system must total at least 50 square inches. For exam- ple: If 5 in. pipe is used for distri- bution, the cross section of each is 20 square inches. Three runs of

5in. pipe is minimum. Shut-offs must not be installed on the reg- isters feeding the room with the thermostat. To prevent the duct and motor from overheating 50 square inches of grill/duct must remain open during operation.

WARNING: When the central heating blow- er is in operation it actually removes air from the room containing the fireplace. If this room can be closed off from the rest of the house, (i.e. with a door) a grille with at least 100 square inch open area must be installed to allow the air to get back to the fireplace. Otherwise periodic smoking of the fireplace will be experi- enced.

8)When installing the blowers for the central heating option, a thermodisc must be in- stalled (supplied with one-way damper). Install thermodisc on the inside (top right side) against the back surface using the two screws, lock washers and nuts sup- plied. See diagram 3.

9)Wire fan to a 120 volt, 15 amp breaker through the line voltage thermostat. See wiring diagrams on page 14. If used, the

Diagram 3

thermostat should be located in the principal room heated through the duct system. Do NOT install it in the room the fireplace is built in. Near the fireplace a simple shut-off switch must be installed in series with the thermostat. If the internal blower (Part # 000-912) is also installed, the shut-off switch will be mounted just beside the variable speed control.

Note: Do not install an independent variable speed control on the central heating fan, unless the manufacturer of the central heating fan permits it.

10)Frame around fireplace and ducting as shown. Use metal ducting only; don't use plastic in the chase. The diagram shows some ways of ducting the hot air from the fan. You are not restricted in the size of pipe, as long as the total cross sectional area of all runs combined is not less than 50 square inches. The diagram shows alter- nate fan locations. Only one external fan is allowed.

11)Ducting is tested at 1 in. clearance to fram- ing for the first 6 feet and 1/2 in. thereafter and no stand-offs are required. All ducting should be insulated to reduce heat loss. Use only approved insulation.

Typical Floor Register

16

Regency Z2510 WarmHearth

Page 15 Page 17
Page 16
Image 16
Regency Wraps Z2510L installation manual Typical Floor Register
Page 15 Page 17

Z2510L specifications

The Regency Wraps Z2510L is a standout product in the realm of kitchen essentials, designed with both functionality and aesthetics in mind. This versatile wrap features a range of characteristics that make it an ideal choice for culinary enthusiasts and professional chefs alike.

One of the main features of the Z2510L is its generous length, which measures 25 feet. This prolonged size allows users to wrap a variety of foods, from large cuts of meat to multiple servings of leftovers, without the hassle of using multiple pieces. The wrap's construction includes a durable, high-quality material that is not only strong and puncture-resistant but also maintains its elasticity when stored, ensuring longevity and reliability for repeated use.

In terms of technology, the Z2510L employs a unique non-stick surface that prevents food from sticking to the wrap, allowing for easy removal and presentation. This is particularly beneficial for delicate items such as pastries or roasted vegetables, ensuring that meals are served beautifully without compromising on taste or texture. Moreover, the wrap is microwave-safe, making it an excellent choice for reheating food without the risk of melting or chemical leaching, a common concern with lower-quality wraps.

Another characteristic that sets the Regency Wraps Z2510L apart is its ease of use. The roll is designed with a convenient dispenser that allows for controlled tearing, minimizing waste and maximizing efficiency in the kitchen. This thoughtful design feature is particularly advantageous in busy cooking environments where time is of the essence.

The Z2510L is also environmentally conscious, as it is made from materials that are biodegradable and free from harmful chemicals, appealing to eco-friendly consumers looking to reduce their environmental footprint.

In summary, the Regency Wraps Z2510L combines practicality, quality, and a commitment to sustainability, making it a must-have in any kitchen. Its standard features, user-friendly technology, and eco-conscious materials reflect a modern approach to food storage that meets the demands of today's consumers. Whether it's for wrapping, storing, or reheating, the Z2510L is engineered to uplift the culinary experience, ensuring that both home cooks and professional chefs have the best tools at their disposal.
Top Page Image Contents