Manuals / Brands / Photography / Digital Camera / Ricoh / Photography / Digital Camera

Ricoh FV-L200B1 , Reading the data from the command 00H

1 32

Download 32 pages, 683.38 Kb

22/32

FV-L200B1

User’s Guide Rev. 1.01

【

Example Code

】Reading the data from the command 00H

 Command to send: 02H, 00H, 00H, 01H, 00H, 03H

SOF Device Code Read/Write Page Selection Command Code Data Length Data EOF

(8bit) (6bit) (1bit) (1bit) (8bit) (8bit) (1byte) (8bit)

02H 00H 00H 01H 00H 03H

 Command to receive upon a successful communication: 02H, 01H, 00H, 03H (assuming the data is 00H)

【Sequence for the saving commands to the EEPROM】

Please use the following sequence for saving the commands to the EEPROM.

1) Set “1” to the 80H.0 to enable writing to the EEPROM.

2) Send the save data with the page selection “1”.

3) The camera sends back one of the following receiving codes after writing the EEPROM.

01H: OK

17H: EEPROM write error

4) 80.0H is cleared to “0” automatically after writing the EEPROM.

Note1: The data cannot be saved to the EEPROM when 80H.0 is “0”.

Note2: When saving the consecutive sequence of commands, the above steps, 1) to 4), are necessary only once.

i.e.) saving the commands “10H, 11H, 12H, 13H”, or “22H, 23H, 24H”, etc.

Note3: When saving the non-consecutive sequence of commands, the above steps, 1) to 4), are necess ary for the

same number of times.

i.e.) saving the commands “10H, 13H, 19H, 1BH” or “20H, 23H, 25H”, etc.

SOF Data Length Data EOF

(8bit) (8bit) (n bytes) (8bit)

02H 01H 00H 03H

Contents

Main FV-L200B1 Users Guide Rev. 1.01 Small Cubic Type UXGA CCD Monochrome PoCL Camera Link Camera FV-L200B1 RICOH COMPANY, LTD. Users Guide Table of Contents FV-L200B1 Users Guide Rev. 1.01 1 Connector Specifications 1.1 Camera Link Connector FV-L200B1 Users Guide Rev. 1.01 1.2 Power-I/O Connector FV-L200B1 Users Guide Rev. 1.01 2 Camera Output Timing Charts 2.1 Normal Mode (Setting 10H: 1XX0XXXX) FVAL Video out 2.1.1 Horizontal Timing Video out FV-L200B1 Users Guide Rev. 1.01 2.1.2 Vertical Timing FVAL Video out 2.1.2.1 Normal Full Scanning (Setting 10H: 1XX00XXX, 11H: X000X000) 2.1.2.2 Partial Full Scanning (Settting 10H: 1XX01XXX, 11H: X000X000) FVAL LVAL DVAL Video out FVAL LVAL DVAL Video out FVAL LVAL DVAL Page Video out FV-L200B1 Users Guide Rev. 1.01 2.2 Binning Mode (setting 10H: 1XX1XXXX) FVAL 2.2.1 Horizontal Timing Video out FVAL LVAL DVAL Video out FVAL LVAL DVAL Video out FVAL LVAL DVAL Video out FVAL LVAL DVAL X0 FV-L200B1 Users Guide Rev. 1.01 2.3 Data Order on the Camera Link Output X3 X2 X0 X3 X2 X1 XCLK FV-L200B1 Users Guide Rev. 1.01 2.4 1 Taps Transferring Image1X-1Y 2.5 Pixel Transferring Image 3 Camera Operational Mode 3.1 Normal Mode 3.1.1 Frame Exposure 3.1.2 Electric Shutter FV-L200B1 Users Guide Rev. 1.01 3.2 Pulse Width Trigger Mode 3.2.1 Pulse Width Trigger ModeV-Reset SUB SG Trigger signal Exposure time FV-L200B1 Users Guide Rev. 1.01 3.3 Edge Preset Trigger Mode 3.3.1 Edge Preset Trigger Mode (V-Reset) Trigger signal Exposure time T1' SUB SG Filtering *Note.1 30CLK FV-L200B1 Users Guide Rev. 1.01 3.4 H Reset Mode FV-L200B1 Users Guide Rev. 1.01 4 Communication Protocol 4.1 Communication Method 4.2 Communication Settings 4.3 Communication Format Page Reading the data from the command 00H FV-L200B1 Users Guide Rev. 1.01 4.4 Camera Control Command 4.4.1 Camera Command List Page FV-L200B1 Users Guide Rev. 1.01 4.4.2 Descriptions of the Camera Control Commands Page Page Page Page Page Page RICOH COMPANY, LTD.