Ricoh FV-L200B1 - page 26

26/32

FV-L200B1

User’s Guide Rev. 1.01

Command No.

Command Descriptions

12H:

MOD3[7O0]

[Camera function mode setting 3] Initial data: 0

This sets the following camera function modes.

D[7O0]

D7 D6 D5 D4 D3 D2 D1 D0

D7~D6:

Video Out 00: 10bit 01: 8bit

10: 12bit

11: No function (Prohibited setting. Do not set these values)

D5: Trigger-in connector selection 0: Camera Link (CC1)

1: /IO connector (No.2 Pin)

D4~D3:

Exposure Start Mode 00: Normal 01: Reserved trigger

10 ~11: H reset

D2~D1:

No Function Set always “000”

D0 Look-up table (Gamma) 00: OFF 01: ON

14H:

UART[7O0]

[Communication mode] Initial Data: 01H

This sets the communication modes.

D[7O0]

D7 D6 D5 D4 D3 D2 D1 D0

D7~D2: No Function Set always “000000”

D1~D0: Communication Mode 00: 38,400 bps 01: 9,600 bps

10: 57,600 bps 11: 115,200 bps

1CH:

AGCMAX[7..0]

[AGC maximum limit] Initial data: 255, data range: 0 to 255

Sets the maximum limit for the AGC.

1DH:

ALCTRGT [7..0]

[Target Brightness for ALC] Initial data: 128, data range: 0 to 255

Sets the target brightness for the ALC function (Auto Luminance Control).

1EH:

ALCMODE[7..0]

[ALC mode] Initial data: 0

This sets the ALC modes.

D[7O0]

D7 D6 D5 D4 D3 D2 D1 D0

D7: Long exposure 0: OFF 1: ON

D6 to D2

No Function Set always “00000”

D1 AGC (Auto Gain Control) 0: OFF 1: ON

D0 AE (Auto Exposure) 0: OFF 1: ON

When using AE combined with the long exposure, exposure time is controlled regardless of the frame rate.

Therefore, the frame rate varies depending on the exposure time.

Contents

Main FV-L200B1 Users Guide Rev. 1.01 Small Cubic Type UXGA CCD Monochrome PoCL Camera Link Camera FV-L200B1 RICOH COMPANY, LTD. Users Guide Table of Contents FV-L200B1 Users Guide Rev. 1.01 1 Connector Specifications 1.1 Camera Link Connector FV-L200B1 Users Guide Rev. 1.01 1.2 Power-I/O Connector FV-L200B1 Users Guide Rev. 1.01 2 Camera Output Timing Charts 2.1 Normal Mode (Setting 10H: 1XX0XXXX) FVAL Video out 2.1.1 Horizontal Timing Video out FV-L200B1 Users Guide Rev. 1.01 2.1.2 Vertical Timing FVAL Video out 2.1.2.1 Normal Full Scanning (Setting 10H: 1XX00XXX, 11H: X000X000) 2.1.2.2 Partial Full Scanning (Settting 10H: 1XX01XXX, 11H: X000X000) FVAL LVAL DVAL Video out FVAL LVAL DVAL Video out FVAL LVAL DVAL Page Video out FV-L200B1 Users Guide Rev. 1.01 2.2 Binning Mode (setting 10H: 1XX1XXXX) FVAL 2.2.1 Horizontal Timing Video out FVAL LVAL DVAL Video out FVAL LVAL DVAL Video out FVAL LVAL DVAL Video out FVAL LVAL DVAL X0 FV-L200B1 Users Guide Rev. 1.01 2.3 Data Order on the Camera Link Output X3 X2 X0 X3 X2 X1 XCLK FV-L200B1 Users Guide Rev. 1.01 2.4 1 Taps Transferring Image1X-1Y 2.5 Pixel Transferring Image 3 Camera Operational Mode 3.1 Normal Mode 3.1.1 Frame Exposure 3.1.2 Electric Shutter FV-L200B1 Users Guide Rev. 1.01 3.2 Pulse Width Trigger Mode 3.2.1 Pulse Width Trigger ModeV-Reset SUB SG Trigger signal Exposure time FV-L200B1 Users Guide Rev. 1.01 3.3 Edge Preset Trigger Mode 3.3.1 Edge Preset Trigger Mode (V-Reset) Trigger signal Exposure time T1' SUB SG Filtering *Note.1 30CLK FV-L200B1 Users Guide Rev. 1.01 3.4 H Reset Mode FV-L200B1 Users Guide Rev. 1.01 4 Communication Protocol 4.1 Communication Method 4.2 Communication Settings 4.3 Communication Format Page Reading the data from the command 00H FV-L200B1 Users Guide Rev. 1.01 4.4 Camera Control Command 4.4.1 Camera Command List Page FV-L200B1 Users Guide Rev. 1.01 4.4.2 Descriptions of the Camera Control Commands Page Page Page Page Page Page RICOH COMPANY, LTD.