4.4.2Descriptions of the Camera Control Commands
(The underline settings are the factory default settings)
Command No. |
|
|
|
|
|
|
|
|
| Command Descriptions |
|
|
| |||
10H: | [Camera function mode setting 1] Initial data: 09H |
|
|
| ||||||||||||
MOD1[70] | This sets the following camera function mode. |
|
|
|
|
|
| |||||||||
| D[70] |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| D7 | D6 | D5 | D4 |
| D3 | D2 |
| D1 |
| D0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| D7: |
| Continuous / Trigger Mode |
| 0: Auto |
| 1: Manual | ||||||||
|
| D6: |
| Trigger Polarity |
|
|
| 0: Positive |
| 1: Negative | ||||||
|
| D5: |
| Trigger Mode |
|
|
| 0: Edge Preset |
| 1: Pulse Width | ||||||
|
| D4: |
| Binning Mode |
|
|
| 0: OFF (Normal) |
| 1: ON (Binning) | ||||||
|
| D3: |
| Scanning Mode |
|
|
| 0: Full scanning | 1: Partial scanning | |||||||
|
| D2 to D0: | Reset Mode |
|
|
|
| 000: NonReset | 001: VReset | |||||||
|
|
|
|
|
|
|
|
|
|
| 010~111: No function |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| (Prohibited setting. Please do not use these) | ||||
| When D7 is set to “0: Auto”, a camera will detect its operational mode based on the input trigger signal. | |||||||||||||||
| If the input trigger signal is kept at high, the camera operates in the continuous mode, assuming the trigger polarity | |||||||||||||||
| is set to positive. |
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| |||||||||
11H: | [Camera function mode setting 2] Initial data: 0 |
|
|
|
|
|
| |||||||||
MOD2[70] | This sets the following camera function modes. |
|
|
|
|
|
| |||||||||
| D[70] |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| D7 | D6 | D5 | D4 |
| D3 | D2 |
| D1 |
| D0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| D7 |
| HD / VD direction |
|
| 00H: SP2 and SP3 as inputs |
| 01H: SP2 and SP3 as outputs | |||||||
|
|
|
|
|
|
|
|
|
| 10 to 11H: (Prohibited setting. Do not set these values) | ||||||
|
| D6 to D5 | Frame rate |
|
|
| 00H: 15.3 fps |
| 01H:7.6 fps | |||||||
|
|
|
|
|
|
|
|
|
| 10H: 3.8 fps |
| 11H: No function | ||||
|
| D4 |
| Smear Half Reduction | 0: OFF |
| 1: ON | |||||||||
|
| D3 |
| Function Mode |
|
| 0: Trigger Mode |
| 1: Continuous Mode | |||||||
|
| D2 to D0: | Partial Scanning |
|
| 000: Full scanning |
| 001: 1/2 partial scanning | ||||||||
|
|
|
|
|
|
|
|
|
| 010: 1/4 partial scanning |
| 111: Variable partial scanning | ||||
|
|
|
|
|
|
|
|
|
| 011~110: No function (Prohibited setting. Do not set these values) | ||||||
| Function mode is enabled when the “Continuous/Trigger” mode selection (MOD[7] is manual (set as 1). | |||||||||||||||
| No video output without the trigger signal input while the camera works with the trigger mode. | |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FVL200B1 | 25/32 | |
User’s Guide Rev. 1.01 | ||
|
