Command No. |
|
|
|
|
|
|
|
|
|
| Command Descriptions |
| |
A0H: |
| [Pixel defect correction mode] Initial data: PDC0[7..0] = 0 |
| ||||||||||
PDC0[70] |
| D[7..0] |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| D7 |
| D6 | D5 | D4 |
| D3 | D2 | D1 | D0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| D7: |
| Write the correction index | 0 1 |
| |||||||
|
|
|
|
| *Writes the coordinates of the command, A2 to A5, to the index number specified by the | ||||||||
|
|
|
|
| command A1. |
|
|
|
|
| |||
|
|
|
|
| *This bit is cleared to “0” automatically after the execution of the command. |
| |||||||
|
| D6 |
| Read the correction index | 0 1 |
| |||||||
|
|
|
|
| *Reads the coordinates of the index number specified by A1 and loads them to the command, | ||||||||
|
|
|
|
| A6 to A9. |
|
|
|
|
|
| ||
|
|
|
|
| *This bit is cleared to “0” automatically after the execution of the command. |
| |||||||
|
| D5: |
| Save to the EEPROM |
| 0 1 |
| ||||||
|
|
|
|
| *Writes the coordinates of all 16 index numbers to the EEPROM. |
| |||||||
|
|
|
|
| *This bit is cleared to “0” automatically after the execution of the command. |
| |||||||
|
| D4 to D2 | No function |
|
|
| Always set as “000” |
| |||||
|
| D1 |
| Correction indices display | 0: OFF | 1: ON | |||||||
|
| D0 |
| Pixel defect correction |
| 0: OFF | 1: ON | ||||||
|
|
|
| ||||||||||
A1H: |
| [Pixel defect correction index number]Initial data: PDC1[7..0] = 0, data range: 0 to 15 |
| ||||||||||
PDC0[70] |
| D[7..0] |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| D7 |
| D6 | D5 | D4 |
| D3 | D2 | D1 | D0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| D7 to D4: | No function |
|
|
| Always set as “0000” |
| |||||
|
| D3 to D0: | Index number |
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
| |||||
A2H: |
| [PDC X coordinate (Write)] |
|
|
|
|
|
| |||||
PDC_WX[70] |
| Initial data: PDC_WX[15..0] =0, data range: 0 to the number of horizontal pixels of the effective area | |||||||||||
A3H |
| Set the X coordinate of pixel defect. |
|
|
|
| |||||||
PDC_WX[158] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
A4H: |
| [PDC Y coordinate (Write)] |
|
|
|
|
|
| |||||
PDC_WY[70] |
| Initial data: PDC_WY[15..0] = 0, data rage: 0 to the number of vertical pixels of the effective area | |||||||||||
A5H |
| Sets the Y coordinate of pixel defect. |
|
|
|
| |||||||
PDC_WY[158] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
A6H: |
| [PDC X coordinate (Read)] |
|
|
|
|
|
| |||||
PDC_RX[70] |
| Initial data: PDC_RX[15..0] = 0, data rage: 0 to the number of vertical pixels of the effective area | |||||||||||
A7H |
| The X coordinate of pixel defect will be loaded when reading. |
| ||||||||||
PDC_RX[158] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
A8H: |
| [PDC Y coordinate (Read)] |
|
|
|
|
|
| |||||
PDC_RY[70] |
| Initial data: PDC_RY[15..0] = 0, data rage: 0 to the number of vertical pixels of the effective area | |||||||||||
A9H |
| The Y coordinate of pixel defect will be loaded when reading. |
| ||||||||||
PDC_RY[158] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
C0H: [70] |
| [Lower limit of the electronic shutter] Initial data: 1; data range: 0 to 4,095 |
| ||||||||||
C1H: [70] |
| Sets the upper limit of the electronic shutter in horizontal lines when using AE (auto exposure). | |||||||||||
|
|
|
| ||||||||||
C2H: [70] |
| [Upper limit of the electronic shutter] Initial data: 4,095; data range: 0 to 4,095 |
| ||||||||||
C3H: [70] |
| Sets the upper limit of the electronic shutter in horizontal lines when using AE (auto exposure). | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FVL200B1 | 30/32 | |
User’s Guide Rev. 1.01 | ||
|
