Ricoh G1168604A 74

Installing Options

F Align the power cable to the left side groove of the duplex unit, and then slide the duplex unit in until it is connected to the printer.

❒After finishing installation, you can check the duplex unit is properly in- stalled: Print the configuration page from the “List/Test Print” menu. If the new device is listed in the column of configuration options, then it has been properly installed.

❒If the duplex unit is not installed properly, repeat the procedure from the start. If you cannot install it properly even after reinstallation, contact your sales or service representative.

❒If the printing position is not correct, adjust the registration of the trays. For more information about adjusting the registration of the trays, see “Adjust- ing Tray Registration”, Maintenance Guide.

For printing the configuration page, see p.32 “Test Printing”.

Contents

Setup Guide Attaching Paper Feed Unit Type Attaching Envelope Feeder Type 610 Attaching 1394 Interface Unit Type 4510 Attaching Hard Disk Drive Type 2600 Attaching Duplex Unit AD610 Trademarks Safety Information Page Page Page Positions of RWARNING and RCAUTION labels ENERGY STAR Program ❖Low-powerMode (Energy Saver mode) ❖Specifications Manuals for This Printer ❖Setup Guide (this manual) ❖Maintenance Guide ❖Software Guide (HTML) How to Read This Manual Exterior 9.Front Cover Release Button 10.Power Switch 11.Paper Tray (Tray 1) 12.Friction Pad 13.Paper Tray Cover Inside Control Panel 9.{Escape}key 10.{# Enter}key keys Where to Put the Printer ❖Space Required for Installation ❖Optimum Environmental Conditions ❖Environments to Avoid ❖Power Source Unpacking the Printer and Checking the Contents of the Box ❖Manuals and CD-ROMs ❖Parts Page Installing the Toner Cartridge Page Page Page Loading Paper C Load the new paper into paper tray with print side up D Carefully slide the paper tray into the printer until it stops Turning the Power On Selecting the Display Language Ready Test Printing E Press the {Online}key Available Options Option Installation Flow Chart Installing Options ❖Exterior ❖Interior Page Attaching Paper Feed Unit Type ❖Paper Feed Unit (including a paper tray) Page Page Attaching Envelope Feeder Type ❖Envelope Feeder Page Attaching Memory Unit Type C 256MB (SDRAM Module) Page Page Page Page Attaching 1394 Interface Unit Type ❖1394 Interface Unit Type ❖1394 Interface Cable (6 pins x 4 pins) ❖1394 Interface Cable (6 pins x 6 pins) Page I Attach the 1394 interface unit to the controller board Page Page Attaching 802.11b Interface Unit Type F ❖802.11b Interface Unit Type F Page Page Page Page Page Page Attaching Bluetooth Interface Unit Type C ❖Bluetooth Interface Unit Type C Page Page Page Page Page Page Attaching Hard Disk Drive Type ❖Hard Disk Drive Type Page Attaching Network Data Protection Unit Type B ❖Network Data Protection Unit Type B Page Attaching Duplex Unit AD610 ❖Duplex Unit D Open the rear cover by pushing the two knobs as shown in the illustra- tion E Remove the rear cover in the horizontal direction Page Network Connection Page USB Connection Parallel Connection IEEE 1394 Connection Ethernet Configuration Host Interface Active Protocol: TCP/IP TCP/IP: *Active IP Address: Network Setup: DHCP DHCP: *On Frame Type (NW) Page IEEE 802.11b (Wireless LAN) Configuration Comm. Mode: *802.11 Ad hoc Channel: (1-11)11 SSID: View SSID: [ 0] SSID: [ 1] SSID: [32] AAAAAAAAAAAAAAAA WEP Setting: *Not Active Change WEP Key: WEP Key: [ 1] *k WEP Key: [ 2] **k Error: Enter 10 or 26 characters Error: Enter 5 or 13 characters WEP Key: [26] W Print a configuration page to confirm the settings made IEEE 1394 Configuration IP over IP over 1394: *Active IP Address1394: 19k.022.033.044 IP Address1394: 192.02k.033.044 SCSI print SCSI print: *Active Quick Install Page Install the Operating Instructions