Installing the Pulley Guard, Installing Handwheel

Assembly (continued)

Installing the Pulley Guard

1.From the hardware pack locate the following: From among the loose parts find the following:

4 Pan Head Cross Serrated Screws 3/16-24 x 3/8" Belt Guard

2.With assistance set the jointer upright.

3.Mount the belt guard in place as shown using the four 3/16" screws.

Screw Pan Head Cr
Serr 3/16-24 x 3/8"	Belt Guard
	Belt Guard

NOTE: Fence mount removed for clarity

Installing Handwheel

1.	From the hardware pack find the following:
	1	Screw Pan Head 1/4-20 x 5/8
	1	Washer 1/4
	1	Washer 1/4	Screw Pan Head w/Washer
2.	From among the loose parts find the following:		Screw Pan Head w/Washer
2.	From among the loose parts find the following:		1/4-20 x 5/8"
		Handwheel	1/4-20 x 5/8"

1 Handwheel

3.Slip the handwheel onto the infeed table elevation shaft and install the washer and screw as shown.

Page 16

Image 16

RIDGID JP0610 manual Installing the Pulley Guard, Installing Handwheel, Serr 3/16-24 x 3/8 Belt Guard, 20 x 5/8

Contents

235$725·60$18$ Table of Contents Safety Instructions For Jointer/Planer Before Using the Jointer/Planer Major Hazards Safety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your Workpiece Whenever Jointer/Planer Is Running Before Leaving the Jointer/PlanerKeep Children Away Don’t Force Tool Power Supply and Motor Specifications Motor Specifications and Electrical RequirementsGlossary of Terms for Woodworking General Electrical Connections Volt, 60 Hz. Tool InformationChanging Motor Voltage Prong Plug Properly Grounded Outlet Grounding Wire Sizes Motor Safety ProtectionExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Loose Parts From Hardware Pack Serrated Hex Bolt Assembly Cabinet and Motor Mount Assembly Install the Leveling Feet Serrated Flange Hex Nut 5/16 Motor Assembly With SwitchMounting the Motor Carriage Head Bolt 16-18 x 1/2 Mounting Jointer Table to Cabinet Tensioning Belt and Installing Rear PanelAlign Belt Tighten Motor Mount Nuts Installing the Pulley Guard Installing HandwheelSerr 3/16-24 x 3/8 Belt Guard 20 x 5/8 Adjusting Table Extension Attach Sawdust ChuteTool Storage Sawdust Chute Screw Wing 1/4-20 x 5/8 Outfeed Socket Head Screw Extension even with Outfeed table Install Cutter Head Guard Assembly Fence Nut MountAssemble Fence To Bed Fence Lock Knob Nut Washer 1/2 Actual Size Not Adjusting Guard Spring Adjusting the Leveling FeetCutter Head Guard Functional Check Pan Head Screw KnobPage On-Off Switch Angle Gauge Cutter Knife Alignment/Adjustments Alignments Cutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface Edge Outfeed Table Adjustment Adjusting Table Gibs Fence Tilt Use and Bevel Stop AdjustmentAngle Gauge Use Stop Screw Bar Before Each Use Safety Instructions for Basic Jointer/Planer OperationFence Slide Lock Knob Bevel Lock Handle Always Use Push Blocks When Planing, Beveling Or Chamfering Feeding the Workpiece All OperationsPush blocks and push sticks Plan your work Inspect your workpiece Before Leaving the jointer/planer Basic Jointer/Planer Cutting Operations Depth of Cut Handwheel OperationStop Pin Operation Feeding the Workpiece Planing JointingBeveling/Chamfering Jointing Without Push Blocks Using the Hold-Down/Push-Blocks RabbetingSupport Long Workpieces Face Rabbet End Edge Sliding Fence Operation Sliding Lock Knob Maintenance and Lubrication Wiring DiagramMaintenance Lubrication General Troubleshooting GuideTrouble Probable Cause Remedy Motor Repair Parts 2120 45 46 Always order by Part Number Not by Key Number Description Key Description Repair Parts Repair Parts Repair Parts Key Description 118615 Nut Hex 3/8-16 Key Description Repair Parts DAY Satisfaction Guarantee Policy Call

RIDGID JP0610 Installing the Pulley Guard, Installing Handwheel, Serr 3/16-24 x 3/8 Belt Guard

Models: JP0610

Assembly (continued)

Installing the Pulley Guard

Serr 3/16-24 x 3/8"

Belt Guard

Installing Handwheel

1/4-20 x 5/8"

Handwheel