Manuals / RIDGID / Power Tools / Planer

RIDGID JP0610 manual Loose Parts From Hardware Pack, Serrated Hex Bolt

Models: JP0610

1 44

Download 44 pages 56.12 Kb

Page 12

Unpacking and Checking Contents (continued)

Loose Parts (From Hardware Pack)

Wrench Hex-“L” 3mm (1)

Wire Nut (1)

Screw Pan Head (1) w/Washer 1/4-20 x 5/8

Screw Wing w/Washer

1/4-20 x 5/8 (2)

Wrench Box 8mm/10mm (1)

Switch Key (1)

Carriage Head Bolt (22)

5/16-18 x 1/2"

Serrated Flange

Hex Nut (22)

5/16-18

Leveling Feet (4)

Washer (8)

3/8"

Hex Nut (8)

3/8-16

Screw Pan Head Cr Serr (6)

Serrated Hex Bolt (3)

(Machine Screw w/Washer Head)

3/8-16 x 3/4"

3/16-24 x 3/8

Washer (1)

1/2"

T-Nut (1)

These two parts are together in hardware pack

12

Image 12

RIDGID JP0610 manual Loose Parts From Hardware Pack, Serrated Hex Bolt

Contents

235$725·60$18$ Table of Contents Safety Instructions For Jointer/Planer Before Using the Jointer/Planer Major Hazards Safety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your Workpiece Whenever Jointer/Planer Is Running Before Leaving the Jointer/PlanerKeep Children Away Don’t Force Tool Motor Specifications and Electrical Requirements Power Supply and Motor SpecificationsGlossary of Terms for Woodworking General Electrical Connections Volt, 60 Hz. Tool InformationChanging Motor Voltage Prong Plug Properly Grounded Outlet Grounding Motor Safety Protection Wire SizesExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Loose Parts From Hardware Pack Serrated Hex Bolt Assembly Cabinet and Motor Mount Assembly Install the Leveling Feet Serrated Flange Hex Nut 5/16 Motor Assembly With SwitchMounting the Motor Carriage Head Bolt 16-18 x 1/2 Tensioning Belt and Installing Rear Panel Mounting Jointer Table to CabinetAlign Belt Tighten Motor Mount Nuts Installing the Pulley Guard Installing HandwheelSerr 3/16-24 x 3/8 Belt Guard 20 x 5/8 Adjusting Table Extension Attach Sawdust ChuteTool Storage Sawdust Chute Screw Wing 1/4-20 x 5/8 Outfeed Socket Head Screw Extension even with Outfeed table Install Cutter Head Guard Assembly Fence Nut MountAssemble Fence To Bed Fence Lock Knob Nut Washer 1/2 Actual Size Not Adjusting Guard Spring Adjusting the Leveling FeetCutter Head Guard Functional Check Pan Head Screw KnobPage On-Off Switch Angle Gauge Cutter Knife Alignment/Adjustments Alignments Cutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface Edge Outfeed Table Adjustment Adjusting Table Gibs Fence Tilt Use and Bevel Stop AdjustmentAngle Gauge Use Stop Screw Bar Safety Instructions for Basic Jointer/Planer Operation Before Each UseFence Slide Lock Knob Bevel Lock Handle Always Use Push Blocks When Planing, Beveling Or Chamfering Feeding the Workpiece All OperationsPush blocks and push sticks Plan your work Inspect your workpiece Before Leaving the jointer/planer Basic Jointer/Planer Cutting Operations Depth of Cut Handwheel OperationStop Pin Operation Feeding the Workpiece Planing JointingBeveling/Chamfering Jointing Without Push Blocks Using the Hold-Down/Push-Blocks RabbetingSupport Long Workpieces Face Rabbet End Edge Sliding Fence Operation Sliding Lock Knob Maintenance and Lubrication Wiring DiagramMaintenance Lubrication Troubleshooting Guide GeneralTrouble Probable Cause Remedy Motor Repair Parts 2120 45 46 Always order by Part Number Not by Key Number Description Key Description Repair Parts Repair Parts Repair Parts Key Description 118615 Nut Hex 3/8-16 Key Description Repair Parts DAY Satisfaction Guarantee Policy Call