Key Description | RIDGID JP0610 specification

Repair Parts

Parts List for RIDGID 6-1/8" Jointer/Planer

Model No. JP06101

RIDGID parts are available on-line at www.ridgidparts.com

	Figure 4
1	8
	7
2	9
	6

3	5	8
		8

4		10
		10

11

12

13

14 10

11

Always order by Part Number - Not by Key Number

	Key	Part No.	Description
	No.	Part No.	Description
	No.


	1	824886	Screw 1/4-28 x 7mm
	2	824885	Wedge
	3	AC8600	† Blade
	4	821030	Screw Flat Hd Hex Soc
			M5 x 0.8-12
	5	818654-7	Key
	6	820722-5	Bearing
	7	824881-1	Support Bearing

	Key	Part No.	Description
	No.	Part No.	Description
	No.


	8	160033-1	* Soc Set Screw 1/4-20 x 3/8
	9	824888	Pulley
	10	818826-8	* Lockwasher M10
	11	824890	Screw Hex 3/8-24 x 3-1/2
	12	828399	Cutter head
	13	820722-6	Bearing
	14	824879-1	Support Bearing

†These parts are available where you purchased your jointer.

42

Image 42

RIDGID JP0610 manual Key Description

Contents

235$725·60$18$ Table of Contents Safety Instructions For Jointer/Planer Before Using the Jointer/Planer Major Hazards Safety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your Workpiece Keep Children Away Whenever Jointer/Planer Is RunningBefore Leaving the Jointer/Planer Don’t Force Tool Motor Specifications and Electrical Requirements Power Supply and Motor SpecificationsGlossary of Terms for Woodworking Changing Motor Voltage General Electrical ConnectionsVolt, 60 Hz. Tool Information Prong Plug Properly Grounded Outlet Grounding Motor Safety Protection Wire SizesExtension Gauge A.W.G Cord Length Unpacking and Checking Contents Loose Parts Loose Parts From Hardware Pack Serrated Hex Bolt Assembly Cabinet and Motor Mount Assembly Mounting the Motor Install the Leveling FeetSerrated Flange Hex Nut 5/16 Motor Assembly With Switch Carriage Head Bolt 16-18 x 1/2 Tensioning Belt and Installing Rear Panel Mounting Jointer Table to CabinetAlign Belt Tighten Motor Mount Nuts Serr 3/16-24 x 3/8 Belt Guard Installing the Pulley GuardInstalling Handwheel 20 x 5/8 Tool Storage Sawdust Chute Screw Wing 1/4-20 x 5/8 Adjusting Table ExtensionAttach Sawdust Chute Outfeed Socket Head Screw Extension even with Outfeed table Assemble Fence To Bed Install Cutter Head GuardAssembly Fence Nut Mount Fence Lock Knob Nut Washer 1/2 Actual Size Not Cutter Head Guard Functional Check Adjusting Guard SpringAdjusting the Leveling Feet Pan Head Screw KnobPage On-Off Switch Angle Gauge Cutter Knife Alignment/Adjustments Alignments Cutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface Edge Outfeed Table Adjustment Angle Gauge Use Adjusting Table GibsFence Tilt Use and Bevel Stop Adjustment Stop Screw Bar Safety Instructions for Basic Jointer/Planer Operation Before Each UseFence Slide Lock Knob Bevel Lock Handle Push blocks and push sticks Always Use Push Blocks When Planing, Beveling Or ChamferingFeeding the Workpiece All Operations Plan your work Inspect your workpiece Before Leaving the jointer/planer Stop Pin Operation Basic Jointer/Planer Cutting OperationsDepth of Cut Handwheel Operation Feeding the Workpiece Beveling/Chamfering PlaningJointing Jointing Without Push Blocks Support Long Workpieces Using the Hold-Down/Push-BlocksRabbeting Face Rabbet End Edge Sliding Fence Operation Sliding Lock Knob Maintenance Maintenance and LubricationWiring Diagram Lubrication Troubleshooting Guide GeneralTrouble Probable Cause Remedy Motor Repair Parts 2120 45 46 Always order by Part Number Not by Key Number Description Key Description Repair Parts Repair Parts Repair Parts Key Description 118615 Nut Hex 3/8-16 Key Description Repair Parts DAY Satisfaction Guarantee Policy Call