To replace the blade, Wrench Large, Throat | RIDGID R4516 specs

adjustments

WARNING:

Before performing any adjustment, make sure the tool is unplugged from the power supply and the switch is in the OFF ( O ) position. Fail- ure to heed this warning could result in serious personal injury.

To avoid unnecessary set-ups and adjustments, a good practice is to check your setups carefully with a framing square and make practice cuts in scrap wood before making finish cuts in good workpieces. Do not start any adjustments until you have checked with a square and made test cuts to be sure adjustments are needed.

SMALL blade

WRENCH

LARGE

blade WRENCH

Fig. 42

TO replace the blade

See Figures 42 - 44.

NOTE: Arbor shaft has right-hand threads.

 Unplug the saw.

 Lower the saw blade and remove the throat plate.

 Raise the saw blade to full height then remove the blade

guard and anti-kickback pawls.

 Make sure the bevel locking lever is locked.

 Insert the open end of the small blade wrench onto the

flats on the arbor shaft.

 Insert the closed end of the large wrench over the hex

nut. Holding both wrenches firmly, pull the outside wrench

(right side) forward while pushing the inside (left side) to

the back of the saw.

 Unlock the release locking lever and remove the blade.

inner Blade

washer

spacer

Blade	OUTER Blade
	washer

Blade

nut

release lever

To install a standard blade:

Place the new blade on the arbor shaft (blade teeth must point down toward the front of the saw to work properly).

Place the blade washer and the blade nut over the arbor shaft. Be sure the dome side of the blade washer faces out from the blade and that all items are snug against the arbor housing. Make sure the blade nut is securely tightened. Do not overtighten.

Lock the release lever.

Rotate the blade by hand to make sure it turns freely.

Lower the saw blade and reinstall the throat plate.

NOTE: To replace the blade with an accessory blade, fol- low the instructions provided with the accessory.

arbor
shaft	Fig. 43

THROAT

PLATEspreader/

RIVING KNIFE

BLADE

Fig. 44

33

Image 33

RIDGID R4516 manual To replace the blade, Wrench Large, Throat, Riving Knife Blade

Contents

OPERATOR’S Manual Introduction Table of Contents Read ALL Instructions General Safety Rules Specific Safety Rules  Never Start a Tool When ANY ROTATiNG COMPonent is in Contact with the Workpiece Specific Safety Rules Symbols Symbol Signal Meaning Service Electrical Speed and WiringExtension Cords Electrical Connection Arbor Anti-Kickback Pawls radial arm and table sawsBevel Cut Chamfer Product Specifications Features See Figure Know Your Table SAW Switch KEY Removed Power SwitchOperating Components To Turn Your SAW on Framing Square Phillips Screwdriver CombinationSQUAREFlat Blade Screwdriver Following items are included with your table saw Loose Parts To install the Handle assembly AssemblyUnpacking Mounting Holes Raising and Lowering the Handle To Store the table saw AccessoriesTo move the saw Miter To Change Between a spreader and a riving knife To remove/replace the Throat PlateThroat Plate Unlocked To Install the ANTI-KICKBACK Pawls and Blade Guard To check SAW Blade installationLarge Small Bladeblade Wrench Wrench ANTI-KICKBACK Pawls To Check and Align the spreader/ riving knife and Saw Blade Screw SpreaderFraming Square Applications OperationCauses of Kickback Avoiding Kickback HOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard Push Blocks Types of cuts See Figure Cutting Tips To Change Blade Depth To Adjust the Bevel indicatorTo Change Blade Angle To lock To unlock Bevel locking Lever To Set the rip fence Scale indicator to the Blade To use the Rip FenceRear LIP To use the sliding table extension To use the miter gaugeLock Knob Miter Gauge Fence Sliding table Extension Locking Lever Scale See Figures 28 Heeling paralleling the blade to the miter gauge grooveIf the distances are different Bolts To make a cross cut Switch KEY Switch in Locked PositionSee Figures 31 Cross CUT Place Left Hand on Workpiece Making a miter cut Making a RIP cut Making a bevel cross cut Adjusting Handwheel Bevel Cross CUT BladeMaking a bevel rip cut Viewed from the FRONT, below the Table SAW Making a Large Panel cut Making a compound bevel miter cutBevel RIP CUT Compound Bevel Miter CUT Making a NON-THROUGH cut Adjusting Handwheel SupportsLarge Panel CUT RIP Fence Once all non-through cuts are completed Once all dado cuts are completed NON-THROUGH CUT Blade Guard Removed Push Stick Dado CUT Wrench Large To replace the bladeThroat Riving Knife Blade To SET the blade at 0 Adjustment Bolt BladeSee Figures 45 If the blade is not perfectly vertical Adjustable To Adjust the miter gaugeTo Check the Alignment of the RIP Fence to the Blade Stop Screw Accessories MaintenanceGeneral Lubrication Problem Cause Solution Troubleshooting Problem Cause DAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not Covered Model No R4516 Serial No Customer Service Information