Customer Service Information

OPERATOR'S MANUAL

10 in. TABLE SAW

R4516

For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgidwoodworking.com.

The model number of this tool is found on a plate attached to the motor housing. Please record the serial number in the space provided below. When ordering repair parts, always give the following information:

Model No.		R4516
Model No.
Serial No.

987000-415

8-24-09 (REV:04)

Page 40

Image 40

RIDGID manual Customer Service Information, Model No R4516 Serial No

Contents

OPERATOR’S Manual Table of Contents Introduction General Safety Rules Read ALL Instructions  Never Start a Tool When ANY ROTATiNG COM Specific Safety RulesPonent is in Contact with the Workpiece Specific Safety Rules Symbols Service Symbol Signal Meaning Speed and Wiring ElectricalExtension Cords Electrical Connection Anti-Kickback Pawls radial arm and table saws ArborBevel Cut Chamfer Features Product Specifications Know Your Table SAW See Figure Power Switch Switch KEY RemovedOperating Components To Turn Your SAW on Combination Framing Square Phillips ScrewdriverSQUAREFlat Blade Screwdriver Loose Parts Following items are included with your table saw Assembly To install the Handle assemblyUnpacking Mounting Holes To Store the table saw Accessories Raising and Lowering the HandleTo move the saw Miter To remove/replace the Throat Plate To Change Between a spreader and a riving knifeThroat Plate Unlocked To check SAW Blade installation To Install the ANTI-KICKBACK Pawls and Blade GuardLarge Small Bladeblade Wrench Wrench ANTI-KICKBACK Pawls Screw Spreader To Check and Align the spreader/ riving knife and Saw BladeFraming Square Operation ApplicationsCauses of Kickback Avoiding Kickback HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard Push Blocks Cutting Tips Types of cuts See Figure To Adjust the Bevel indicator To Change Blade DepthTo Change Blade Angle To lock To unlock Bevel locking Lever To use the Rip Fence To Set the rip fence Scale indicator to the BladeRear LIP To use the miter gauge To use the sliding table extensionLock Knob Miter Gauge Fence Sliding table Extension Locking Lever Scale Heeling paralleling the blade to the miter gauge groove See Figures 28If the distances are different Bolts Switch KEY Switch in Locked Position To make a cross cutSee Figures 31 Cross CUT Place Left Hand on Workpiece Making a RIP cut Making a miter cut Adjusting Handwheel Bevel Cross CUT Blade Making a bevel cross cutMaking a bevel rip cut Viewed from the FRONT, below the Table SAW Making a compound bevel miter cut Making a Large Panel cutBevel RIP CUT Compound Bevel Miter CUT Adjusting Handwheel Supports Making a NON-THROUGH cutLarge Panel CUT RIP Fence Once all non-through cuts are completed NON-THROUGH CUT Blade Guard Removed Push Stick Dado CUT Once all dado cuts are completed To replace the blade Wrench LargeThroat Riving Knife Blade Adjustment Bolt Blade To SET the blade at 0See Figures 45 If the blade is not perfectly vertical To Adjust the miter gauge AdjustableTo Check the Alignment of the RIP Fence to the Blade Stop Screw Maintenance AccessoriesGeneral Lubrication Troubleshooting Problem Cause Solution Problem Cause Warranty DAY Satisfaction Guarantee PolicyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not Covered Customer Service Information Model No R4516 Serial No

OPERATOR'S MANUAL

10 in. TABLE SAW

R4516

Customer Service Information

Model No.

R4516

Serial No.