Symbols | RIDGID R4516 instruction

SYMBOLS

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper inter- pretation of these symbols will allow you to operate the tool better and safer.

	Safety Alert	Indicates a potential personal injury hazard.
	Read Operator’s Manual	To reduce the risk of injury, user must read and understand
	Read Operator’s Manual	operator’s manual before using this product.
		operator’s manual before using this product.
	Eye Protection	Always wear eye protection marked to comply with ANSI
	Eye Protection	Z87.1.
		Z87.1.
	No Hands Symbol	Failure to keep your hands away from the blade will result in
	No Hands Symbol	serious personal injury.
		serious personal injury.
	Wet Conditions Alert	Do not expose to rain or use in damp locations.
	Pinch Warning	Always watch for movement paying extra attention to
	Pinch Warning	potential areas where pinching could occur.
		potential areas where pinching could occur.
V	Volts	Voltage
A	Amperes	Current
Hz	Hertz	Frequency (cycles per second)
W	Watt	Power
min	Minutes	Time
	Alternating Current	Type of current
	Direct Current	Type or a characteristic of current
no	No Load Speed	Rotational speed, at no load
	Class II Construction	Double-insulated construction
.../min	Per Minute	Revolutions, strokes, surface speed, orbits etc., per minute

6

Image 6

RIDGID R4516 manual Symbols

Contents

OPERATOR’S Manual Table of Contents Introduction General Safety Rules Read ALL Instructions Specific Safety Rules  Never Start a Tool When ANY ROTATiNG COMPonent is in Contact with the Workpiece Specific Safety Rules Symbols Service Symbol Signal Meaning Extension Cords Speed and WiringElectrical Electrical Connection Bevel Cut Anti-Kickback Pawls radial arm and table sawsArbor Chamfer Features Product Specifications Know Your Table SAW See Figure Operating Components Power SwitchSwitch KEY Removed To Turn Your SAW on Framing Square Phillips Screwdriver CombinationSQUAREFlat Blade Screwdriver Loose Parts Following items are included with your table saw Unpacking AssemblyTo install the Handle assembly Mounting Holes To move the saw To Store the table saw AccessoriesRaising and Lowering the Handle Miter Throat Plate To remove/replace the Throat PlateTo Change Between a spreader and a riving knife Unlocked Large Small Bladeblade Wrench Wrench To check SAW Blade installationTo Install the ANTI-KICKBACK Pawls and Blade Guard ANTI-KICKBACK Pawls To Check and Align the spreader/ riving knife and Saw Blade Screw SpreaderFraming Square Causes of Kickback OperationApplications Avoiding Kickback Featherboard HOW to Make a FeatherboardHOW to Mount a Featherboard Push Blocks Cutting Tips Types of cuts See Figure To Change Blade Angle To Adjust the Bevel indicatorTo Change Blade Depth To lock To unlock Bevel locking Lever To Set the rip fence Scale indicator to the Blade To use the Rip FenceRear LIP Lock Knob Miter Gauge To use the miter gaugeTo use the sliding table extension Fence Sliding table Extension Locking Lever Scale If the distances are different Heeling paralleling the blade to the miter gauge grooveSee Figures 28 Bolts See Figures 31 Switch KEY Switch in Locked PositionTo make a cross cut Cross CUT Place Left Hand on Workpiece Making a RIP cut Making a miter cut Making a bevel rip cut Adjusting Handwheel Bevel Cross CUT BladeMaking a bevel cross cut Viewed from the FRONT, below the Table SAW Bevel RIP CUT Making a compound bevel miter cutMaking a Large Panel cut Compound Bevel Miter CUT Large Panel CUT RIP Fence Adjusting Handwheel SupportsMaking a NON-THROUGH cut Once all non-through cuts are completed NON-THROUGH CUT Blade Guard Removed Push Stick Dado CUT Once all dado cuts are completed Throat To replace the bladeWrench Large Riving Knife Blade See Figures 45 Adjustment Bolt BladeTo SET the blade at 0 If the blade is not perfectly vertical To Check the Alignment of the RIP Fence to the Blade To Adjust the miter gaugeAdjustable Stop Screw General MaintenanceAccessories Lubrication Troubleshooting Problem Cause Solution Problem Cause What is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not Covered Customer Service Information Model No R4516 Serial No