Xcard Resistor Chart, Frequency, 200Hz

Image 18

Rockford Fosgate 50.2 Xcard Resistor Chart, Butterworth Alignment Q =, 1% resistors used with 0.047mF capacitors, 200Hz

Contents

new chrome heatsink powerpower 50.1 PRACTICE SAFE SOUND TABLE OF CONTENTS G E T T I N G S TA R T E D INTRODUCTION TO 50 SERIES PUNCH AMPLIFIER ACCESSORY PACKPunch Power Punch Power TECHNICAL DESIGN FEATURES Stereo Pass-Thru DSM Discrete Surface Mount TechnologyXCard Internal Crossover Balanced Line Inputs NOMAD NOn-MultiplyingAdvanced DecisionITS Increased Thermal Stability 50.2 DESIGN FEATURES M P L I F I E R 50.1 DESIGN FEATURES Page INSTALLATION CONSIDERATIONS Tools Needed Trunk Mounting BATTERY AND CHARGINGMOUNTING LOCATION S Passenger Compartment Mounting WIRING THE SYSTEM USING PASSIVE CROSSOVERS 6dB/Octave Low-Pass TABLE OF CROSSOVER COMPONENT VALUESSpeaker Impedance Freq High-Pass USING THE XCARDCUSTOMIZING THE XCARD Low-Pass 1% resistors used with 0.047mF capacitors XCARD RESISTOR CHARTButterworth Alignment Q = Butterworth Alignment Q = 50.2 INSTALLATION 50.2 Power Connections Option #150.2 Power Connections Option #2 Left Phase Switch set to Stereo OperationStereo/Mono Operation Right Phase Switch set to Left Phase Switch set to Bridged OperationEZ-BridgedOperation Right Phase Switch set to USING THE 50.2 SIGNAL SWITCHING NETWORK 50.2 bypasses the circuitry of XCard 1 and XCard 50.2 uses output from XCard Pass-Thru uses output from XCard 50.2 bypasses the circuitry of XCard 50.2 uses output from XCard 1 and XCard Pass-Thru bypasses XCard 1 and XCard USING THE 50.2 BALANCED LINE INPUTS Connecting the BLT Disconnect Speakers from the Level Setting the BLTPerformance Characteristics AC Voltmeter set to AC Volts 50.1 Power Connections Option #2 50.1 INSTALLATION50.1 Power Connections Option #1 – 26 – Mono Operation Phase Switch set to Phase Switch 50.1 #1/2 set to Stereo/Mono Operation Phase Switch 50.1 #1 set toPhase Switch 50.1 #2 set to XCard 50.1 #1/#2 set to Full Range Bridged Mono Operation Phase Switch 50.1 #1 set toPhase Switch 50.1 #2 set to U S I N G T H E 50.1 SIGNAL S W I T C H I N G N E T W O R K“Audiophile Bypass” the Pass-Thru has Full Range output only Configure a 12dB per octave filter for theXover is set to 12dB LOUD Configure a 24dB per octave filter for the • Xover is set to 24dBPass-Thru has Full Range output only SYSTEM DIAGRAMS 100 Watt System rated @ 4 ohmsTotal Power Delivery RMS Tweeters 150 Watt System rated @ 4 ohmsTotal Power Delivery RMS 400 Watts Tweeters 300 Watt System rated @ 4 ohmsTotal Power Delivery RMS 400 Watts 400 Watts 500 Watt System rated @ 4 ohmsTweeters Midrange ROCKFORD FOSGATE ACCESSORIES NOISEBalanced Line Transmitter FG-BLT Energy Storage Capacitors XCard Crossoverspunch Diagnosis TROUBLESHOOTINGSymptom Remedy Remedy SymptomDiagnosis Speaker Output Low Remedy SymptomDiagnosis Low or distorted output from the Preface QUICK CHECK FOR TROUBLESHOOTING CAR AUDIO SYSTEMSAUTOSOUND 2000s Noise Overview Time for Processors Summation What is an Amplifier? DYNAMIC POWER MEASUREMENTSAbout the Dynamic Power Measurements Music 50Watts 90Watts 150Watts 300Watts 25Watts 50Watts 50.2 SPECIFICATIONSSpecifications subject to change without notice 100Watts 200 Watts 100Watts 200Watts 325Watts 650Watts 50Watts 50.1 SPECIFICATIONSSpecifications subject to change without notice 100Watts 200Watts 400 Watts What is Covered LIMITED WARRANTY INFORMATIONLength of Warranty What is Not Covered N F O R M A T I O N Maletero INTRODUCCIÓNUBICACIÓN DE LOS AMPLIFICADORES Habitáculo ESPAÑOL Operación mono/estéreo MONTAGE InstallationINTRODUCTION Montage dans le coffre FRANÇAIS Opération stéréo/monoTri-modeInput Im Fahrzeugkofferraum EINLEITUNGEINBAUORT Auf der Beifahrerseite DEUTSCH Linken Phasen Schalter auf 0 stellenStereo/Mono Betrieb DOVE POSIZIONARLO InstallazioneINTRODUZIONE Nel Bagagliaio ITALIANO Stereo/Mono OperationFase sinistra dellinterruttore posizionata su MADE IN THE USA

Rockford Fosgate 50.2 Xcard Resistor Chart, Butterworth Alignment Q =, Frequency, 200Hz, 35.7kΩ

Models: 50.1 50.2