Stereo Operation, Stereo/Mono Operation | Rockford Fosgate 50.2

Image 20

Rockford Fosgate 50.2, 50.1 Stereo Operation, Stereo/Mono Operation, Left Phase Switch set to, Right Phase Switch set to

Contents

power powernew chrome heatsink 50.1 PRACTICE SAFE SOUND TABLE OF CONTENTS G E T T I N G S TA R T E D PUNCH AMPLIFIER ACCESSORY PACK Punch PowerINTRODUCTION TO 50 SERIES Punch Power TECHNICAL DESIGN FEATURES XCard Internal Crossover Stereo Pass-ThruDSM Discrete Surface Mount Technology ITS Increased Thermal Stability Balanced Line InputsNOMAD NOn-MultiplyingAdvanced Decision 50.2 DESIGN FEATURES M P L I F I E R 50.1 DESIGN FEATURES Page INSTALLATION CONSIDERATIONS Tools Needed BATTERY AND CHARGING MOUNTING LOCATION STrunk Mounting Passenger Compartment Mounting WIRING THE SYSTEM USING PASSIVE CROSSOVERS TABLE OF CROSSOVER COMPONENT VALUES Speaker Impedance6dB/Octave Low-Pass Freq USING THE XCARD CUSTOMIZING THE XCARDHigh-Pass Low-Pass XCARD RESISTOR CHART Butterworth Alignment Q =1% resistors used with 0.047mF capacitors Butterworth Alignment Q = 50.2 Power Connections Option #2 50.2 INSTALLATION50.2 Power Connections Option #1 Stereo Operation Stereo/Mono OperationLeft Phase Switch set to Right Phase Switch set to Bridged Operation EZ-BridgedOperationLeft Phase Switch set to Right Phase Switch set to USING THE 50.2 SIGNAL SWITCHING NETWORK 50.2 bypasses the circuitry of XCard 1 and XCard 50.2 uses output from XCard Pass-Thru uses output from XCard 50.2 bypasses the circuitry of XCard 50.2 uses output from XCard 1 and XCard Pass-Thru bypasses XCard 1 and XCard USING THE 50.2 BALANCED LINE INPUTS Connecting the BLT Level Setting the BLT Performance CharacteristicsDisconnect Speakers from the AC Voltmeter set to AC Volts 50.1 INSTALLATION 50.1 Power Connections Option #150.1 Power Connections Option #2 – 26 – Mono Operation Phase Switch set to Phase Switch 50.1 #1/2 set to Phase Switch 50.1 #1 set to Phase Switch 50.1 #2 set toStereo/Mono Operation XCard 50.1 #1/#2 set to Full Range Phase Switch 50.1 #2 set to Bridged Mono OperationPhase Switch 50.1 #1 set to “Audiophile Bypass” the U S I N G T H E 50.1 SIGNALS W I T C H I N G N E T W O R K Configure a 12dB per octave filter for the Xover is set to 12dBPass-Thru has Full Range output only LOUD Pass-Thru has Full Range output only Configure a 24dB per octave filter for the• Xover is set to 24dB Total Power Delivery RMS SYSTEM DIAGRAMS100 Watt System rated @ 4 ohms 150 Watt System rated @ 4 ohms Total Power Delivery RMSTweeters 400 Watts 300 Watt System rated @ 4 ohms Total Power Delivery RMSTweeters 400 Watts 500 Watt System rated @ 4 ohms Tweeters400 Watts Midrange Balanced Line Transmitter FG-BLT ROCKFORD FOSGATE ACCESSORIESNOISE punch Energy Storage CapacitorsXCard Crossovers TROUBLESHOOTING SymptomDiagnosis Remedy Symptom DiagnosisRemedy Speaker Output Low Symptom DiagnosisRemedy Low or distorted output from the QUICK CHECK FOR TROUBLESHOOTING CAR AUDIO SYSTEMS AUTOSOUND 2000sPreface Noise Overview Time for Processors Summation DYNAMIC POWER MEASUREMENTS About the Dynamic Power MeasurementsWhat is an Amplifier? Music 50.2 SPECIFICATIONS Specifications subject to change without notice50Watts 90Watts 150Watts 300Watts 25Watts 50Watts 100Watts 200 Watts 50.1 SPECIFICATIONS Specifications subject to change without notice100Watts 200Watts 325Watts 650Watts 50Watts 100Watts 200Watts 400 Watts LIMITED WARRANTY INFORMATION Length of WarrantyWhat is Covered What is Not Covered N F O R M A T I O N INTRODUCCIÓN UBICACIÓN DE LOS AMPLIFICADORESMaletero Habitáculo ESPAÑOL Operación mono/estéreo Installation INTRODUCTIONMONTAGE Montage dans le coffre Tri-modeInput FRANÇAISOpération stéréo/mono EINLEITUNG EINBAUORTIm Fahrzeugkofferraum Auf der Beifahrerseite Stereo/Mono Betrieb DEUTSCHLinken Phasen Schalter auf 0 stellen Installazione INTRODUZIONEDOVE POSIZIONARLO Nel Bagagliaio Fase sinistra dellinterruttore posizionata su ITALIANOStereo/Mono Operation MADE IN THE USA