Balanced Line Inputs | Rockford Fosgate 50.1, 50.2 specification

Image 7

Rockford Fosgate 50.1, 50.2 Balanced Line Inputs, NOMAD NOn-MultiplyingAdvanced Decision, ITS Increased Thermal Stability

Contents

50.1 powerpower new chrome heatsink PRACTICE SAFE SOUND G E T T I N G S TA R T E D TABLE OF CONTENTS Punch Power PUNCH AMPLIFIER ACCESSORY PACKPunch Power INTRODUCTION TO 50 SERIES TECHNICAL DESIGN FEATURES DSM Discrete Surface Mount Technology Stereo Pass-ThruXCard Internal Crossover NOMAD NOn-MultiplyingAdvanced Decision Balanced Line InputsITS Increased Thermal Stability 50.2 DESIGN FEATURES M P L I F I E R 50.1 DESIGN FEATURES Page Tools Needed INSTALLATION CONSIDERATIONS Passenger Compartment Mounting BATTERY AND CHARGINGMOUNTING LOCATION S Trunk Mounting WIRING THE SYSTEM USING PASSIVE CROSSOVERS Freq TABLE OF CROSSOVER COMPONENT VALUESSpeaker Impedance 6dB/Octave Low-Pass Low-Pass USING THE XCARDCUSTOMIZING THE XCARD High-Pass Butterworth Alignment Q = XCARD RESISTOR CHARTButterworth Alignment Q = 1% resistors used with 0.047mF capacitors 50.2 Power Connections Option #1 50.2 INSTALLATION50.2 Power Connections Option #2 Right Phase Switch set to Stereo OperationStereo/Mono Operation Left Phase Switch set to Right Phase Switch set to Bridged OperationEZ-BridgedOperation Left Phase Switch set to USING THE 50.2 SIGNAL SWITCHING NETWORK 50.2 bypasses the circuitry of XCard 1 and XCard Pass-Thru uses output from XCard 50.2 uses output from XCard 50.2 bypasses the circuitry of XCard Pass-Thru bypasses XCard 1 and XCard 50.2 uses output from XCard 1 and XCard Connecting the BLT USING THE 50.2 BALANCED LINE INPUTS AC Voltmeter set to AC Volts Level Setting the BLTPerformance Characteristics Disconnect Speakers from the – 26 – 50.1 INSTALLATION50.1 Power Connections Option #1 50.1 Power Connections Option #2 Phase Switch set to Mono Operation Phase Switch 50.1 #1/2 set to XCard 50.1 #1/#2 set to Full Range Phase Switch 50.1 #1 set toPhase Switch 50.1 #2 set to Stereo/Mono Operation Phase Switch 50.1 #1 set to Bridged Mono OperationPhase Switch 50.1 #2 set to S W I T C H I N G N E T W O R K U S I N G T H E 50.1 SIGNAL“Audiophile Bypass” the LOUD Configure a 12dB per octave filter for theXover is set to 12dB Pass-Thru has Full Range output only • Xover is set to 24dB Configure a 24dB per octave filter for thePass-Thru has Full Range output only 100 Watt System rated @ 4 ohms SYSTEM DIAGRAMSTotal Power Delivery RMS 400 Watts 150 Watt System rated @ 4 ohmsTotal Power Delivery RMS Tweeters 400 Watts 300 Watt System rated @ 4 ohmsTotal Power Delivery RMS Tweeters Midrange 500 Watt System rated @ 4 ohmsTweeters 400 Watts NOISE ROCKFORD FOSGATE ACCESSORIESBalanced Line Transmitter FG-BLT XCard Crossovers Energy Storage Capacitorspunch Remedy TROUBLESHOOTINGSymptom Diagnosis Speaker Output Low SymptomDiagnosis Remedy Low or distorted output from the SymptomDiagnosis Remedy Noise Overview QUICK CHECK FOR TROUBLESHOOTING CAR AUDIO SYSTEMSAUTOSOUND 2000s Preface Summation Time for Processors Music DYNAMIC POWER MEASUREMENTSAbout the Dynamic Power Measurements What is an Amplifier? 100Watts 200 Watts 50.2 SPECIFICATIONSSpecifications subject to change without notice 50Watts 90Watts 150Watts 300Watts 25Watts 50Watts 100Watts 200Watts 400 Watts 50.1 SPECIFICATIONSSpecifications subject to change without notice 100Watts 200Watts 325Watts 650Watts 50Watts What is Not Covered LIMITED WARRANTY INFORMATIONLength of Warranty What is Covered N F O R M A T I O N Habitáculo INTRODUCCIÓNUBICACIÓN DE LOS AMPLIFICADORES Maletero Operación mono/estéreo ESPAÑOL Montage dans le coffre InstallationINTRODUCTION MONTAGE Opération stéréo/mono FRANÇAISTri-modeInput Auf der Beifahrerseite EINLEITUNGEINBAUORT Im Fahrzeugkofferraum Linken Phasen Schalter auf 0 stellen DEUTSCHStereo/Mono Betrieb Nel Bagagliaio InstallazioneINTRODUZIONE DOVE POSIZIONARLO Stereo/Mono Operation ITALIANOFase sinistra dellinterruttore posizionata su MADE IN THE USA

Rockford Fosgate 50.1, 50.2 manual Balanced Line Inputs, NOMAD NOn-MultiplyingAdvanced Decision

Models: 50.1 50.2