Specifications, 100Watts 200 Watts | Rockford Fosgate 50.1, 50.2

Image 49

Rockford Fosgate 50.1, 50.2 manual Specifications subject to change without notice, 100Watts 200 Watts

Contents

power powernew chrome heatsink 50.1 PRACTICE SAFE SOUND G E T T I N G S TA R T E D TABLE OF CONTENTS Punch Power PUNCH AMPLIFIER ACCESSORY PACKINTRODUCTION TO 50 SERIES Punch Power TECHNICAL DESIGN FEATURES DSM Discrete Surface Mount Technology Stereo Pass-ThruXCard Internal Crossover NOMAD NOn-MultiplyingAdvanced Decision Balanced Line InputsITS Increased Thermal Stability 50.2 DESIGN FEATURES M P L I F I E R 50.1 DESIGN FEATURES Page Tools Needed INSTALLATION CONSIDERATIONS MOUNTING LOCATION S BATTERY AND CHARGINGTrunk Mounting Passenger Compartment Mounting WIRING THE SYSTEM USING PASSIVE CROSSOVERS Speaker Impedance TABLE OF CROSSOVER COMPONENT VALUES6dB/Octave Low-Pass Freq CUSTOMIZING THE XCARD USING THE XCARDHigh-Pass Low-Pass Butterworth Alignment Q = XCARD RESISTOR CHART1% resistors used with 0.047mF capacitors Butterworth Alignment Q = 50.2 Power Connections Option #1 50.2 INSTALLATION50.2 Power Connections Option #2 Stereo/Mono Operation Stereo OperationLeft Phase Switch set to Right Phase Switch set to EZ-BridgedOperation Bridged OperationLeft Phase Switch set to Right Phase Switch set to USING THE 50.2 SIGNAL SWITCHING NETWORK 50.2 bypasses the circuitry of XCard 1 and XCard Pass-Thru uses output from XCard 50.2 uses output from XCard 50.2 bypasses the circuitry of XCard Pass-Thru bypasses XCard 1 and XCard 50.2 uses output from XCard 1 and XCard Connecting the BLT USING THE 50.2 BALANCED LINE INPUTS Performance Characteristics Level Setting the BLTDisconnect Speakers from the AC Voltmeter set to AC Volts 50.1 Power Connections Option #1 50.1 INSTALLATION50.1 Power Connections Option #2 – 26 – Phase Switch set to Mono Operation Phase Switch 50.1 #1/2 set to Phase Switch 50.1 #2 set to Phase Switch 50.1 #1 set toStereo/Mono Operation XCard 50.1 #1/#2 set to Full Range Phase Switch 50.1 #1 set to Bridged Mono OperationPhase Switch 50.1 #2 set to S W I T C H I N G N E T W O R K U S I N G T H E 50.1 SIGNAL“Audiophile Bypass” the Xover is set to 12dB Configure a 12dB per octave filter for thePass-Thru has Full Range output only LOUD • Xover is set to 24dB Configure a 24dB per octave filter for thePass-Thru has Full Range output only 100 Watt System rated @ 4 ohms SYSTEM DIAGRAMSTotal Power Delivery RMS Total Power Delivery RMS 150 Watt System rated @ 4 ohmsTweeters 400 Watts Total Power Delivery RMS 300 Watt System rated @ 4 ohmsTweeters 400 Watts Tweeters 500 Watt System rated @ 4 ohms400 Watts Midrange NOISE ROCKFORD FOSGATE ACCESSORIESBalanced Line Transmitter FG-BLT XCard Crossovers Energy Storage Capacitorspunch Symptom TROUBLESHOOTINGDiagnosis Remedy Diagnosis SymptomRemedy Speaker Output Low Diagnosis SymptomRemedy Low or distorted output from the AUTOSOUND 2000s QUICK CHECK FOR TROUBLESHOOTING CAR AUDIO SYSTEMSPreface Noise Overview Summation Time for Processors About the Dynamic Power Measurements DYNAMIC POWER MEASUREMENTSWhat is an Amplifier? Music Specifications subject to change without notice 50.2 SPECIFICATIONS50Watts 90Watts 150Watts 300Watts 25Watts 50Watts 100Watts 200 Watts Specifications subject to change without notice 50.1 SPECIFICATIONS100Watts 200Watts 325Watts 650Watts 50Watts 100Watts 200Watts 400 Watts Length of Warranty LIMITED WARRANTY INFORMATIONWhat is Covered What is Not Covered N F O R M A T I O N UBICACIÓN DE LOS AMPLIFICADORES INTRODUCCIÓNMaletero Habitáculo Operación mono/estéreo ESPAÑOL INTRODUCTION InstallationMONTAGE Montage dans le coffre Opération stéréo/mono FRANÇAISTri-modeInput EINBAUORT EINLEITUNGIm Fahrzeugkofferraum Auf der Beifahrerseite Linken Phasen Schalter auf 0 stellen DEUTSCHStereo/Mono Betrieb INTRODUZIONE InstallazioneDOVE POSIZIONARLO Nel Bagagliaio Stereo/Mono Operation ITALIANOFase sinistra dellinterruttore posizionata su MADE IN THE USA