INSTALLATION

BATTERY AND CHARGING

Amplifiers will put an increased load on the vehicle's battery and charging system. We recommend checking your alternator and battery condition to ensure that the electrical system has enough capacity to handle the increased load of your stereo system. Stock electrical systems which are in good condition should be able to handle the extra load of any Rockford Fosgate amplifier without problems, although battery and alternator life can be reduced slightly. To maximize the performance of your amplifier, we suggest the use of a heavy duty battery and an energy storage capacitor.

WIRING THE SYSTEM

!CAUTION: If you do not feel comfortable with wiring your new unit, please see your local Authorized Rockford Fosgate Dealer for installation.

!CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

CAUTION: Avoid running power wires near the low level input cables, antenna,

!power leads, sensitive equipment or harnesses. The power wires carry substantial current and could induce noise into the audio system.

1.Plan the wire routing. Keep RCA cables close together but isolated from the amplifier's power cables and any high power auto accessories, especially electric motors. This is done to prevent coupling the noise from radiated electrical fields into the audio signal. When feeding the wires through the firewall or any metal barrier, protect them with plastic or rubber grommets to prevent short circuits. Leave the wires long at this point to adjust for a precise fit at a later time.

2.Prepare the RED wire (power cable) for attachment to the amplifier by stripping 1/2" of insulation from the end of the wire. Insert the bared wire into the B+ terminal and tighten the set screw to secure the cable in place.

NOTE: The B+ cable MUST be fused 18" or less from the vehicle's battery. Install the fuseholder under the hood and prepare the cable ends as stated above. Connections should be water tight.

3.Trim the RED wire (power cable) within 18" of the battery and strip1/2"of insulation from the end of the wire. Splice the fuseholder into the power line using appropriate inline connectors. Use the section of cable that was trimmed earlier and connect it to the other end of the fuseholder.

4.Strip 1/2" from the battery end of the power cable and crimp a large ring terminal to the cable. Use the ring terminal to connect to the battery positive terminal. DO NOT install the fuse at this time.

5.Prepare the BLACK wire (Ground cable) for attachment to the amplifier by stripping 1/2" of insulation from the end of the wire. Insert the bared wire into the GND terminal and tighten the set screw to secure the cable in place. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the other end of the wire and attach a ring connector. Fasten the cable to the chassis using a non-anodized screw and a star washer.

6.Prepare the REM turn-on wire for connection to the amplifier by stripping 1/2" of insulation from the wire end. Insert the bared wire into the REM terminal and tighten the set screw to secure the cable into place. Connect the other end of the REM wire to a switched 12 volt positive source.

The switched voltage is usually taken from the source unit's accessory lead. If the source unit does not have this output available, the recommended solution is to wire a mechanical switch in line with a 12 volt source to activate the amplifier.

7.Securely mount the amplifier to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or plastic panels. Doing so may enable the screws to pull out from the panel due to road vibration or sudden vehicle stops.

8.Connect the source signal to the amplifier by plugging the RCA cables into the input jacks at the amplifier.

9.Connect the speakers. Strip the speaker wires 1/2" and insert into the speaker terminal and tighten the set screw to secure into place. Be sure to maintain proper speaker polarity. DO NOT chassis ground any of the speaker leads as unstable operation may result.

6

Page 5 Page 7
Page 6
Image 6
Rockford Fosgate FFX3 manual Installation Battery and Charging, Wiring the System
Page 5 Page 7

FFX3 specifications

The Rockford Fosgate FFX3 is a powerful and versatile amplifier designed to elevate the audio experience in vehicles. Known for its exceptional build quality and performance, the FFX3 is tailored for those who demand clarity and punch from their sound systems. One of the key features of the FFX3 is its Class D amplifier topology, which allows it to deliver significant power output while maintaining high efficiency. This means less heat production and greater reliability, making it ideal for extended listening sessions.

The FFX3 boasts a maximum power output of up to 1,000 watts, enabling it to drive subwoofers and speakers with ease. It comes equipped with a variable low-pass filter that enables users to tailor their sound to perfection, ensuring that the bass is tight and well-defined. Additionally, the amplifier includes high-level inputs, making it compatible with factory-installed audio systems without the need for a signal converter. This flexibility allows users to upgrade their audio systems without extensive modifications.

One of the standout technologies in the FFX3 is its "on-board" signal processing capabilities. The amplifier features adjustable bass boost, allowing listeners to enhance lower frequencies to suit their personal preferences. Moreover, the FFX3 incorporates a thermal protection circuit, safeguarding the amplifier against overheating during intense use. The compact design of the FFX3 makes it easy to install in a variety of locations within a vehicle, ensuring that space constraints won’t be an issue.

The chassis of the FFX3 is rugged and designed to withstand the rigors of automotive environments. Its stylish aesthetics allow it to seamlessly integrate into any car interior while remaining unobtrusive. Further enhancing its versatility, the amplifier includes a remote bass level control, allowing users to adjust their bass output from the front seat for maximum convenience.

In conclusion, the Rockford Fosgate FFX3 is a powerful and efficient audio amplifier that excels in delivering high-quality sound. With its innovative features and solid construction, it is a perfect choice for anyone looking to upgrade their vehicle's audio system. Whether attentive to detail or seeking high-impact bass, the FFX3 promises to enhance any listening experience.
Top Page Image Contents