INSTALLATION

MOUNTING LOCATIONS

Engine Compartment

Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warranty.

Trunk Mounting

Mounting the amplifier vertically or inverted will provide adequate cooling of the amplifier.

Mounting the amplifier on the floor of the trunk will provide the best cooling of the amplifier.

Passenger Compartment Mounting

Mounting the amplifier in the passenger compartment will work as long as you provide a sufficient amount of air for the amplifier to cool itself. If you are going to mount the amplifier under the seat of the vehicle, you must have at least 1" (2.54cm) of air gap around the amplifier's heatsink.

Mounting the amplifier with less than 1" (2.54cm) of air gap around the amplifier's heatsink in the passenger compartment will not provide proper cooling and will severely affect the performance of the amplifier and is strongly not recommended.

BATTERY AND CHARGING

Amplifiers will put an increased load on the vehicle's battery and charging system.We recommend checking your alternator and battery condition to ensure that the electrical system has enough capacity to handle the increased load of your stereo system. Stock electrical systems which are in good condition should be able to handle the extra load of any Punch Series amplifier without problems, although battery and alternator life can be reduced slightly.To maximize the performance of your amplifier, we suggest the use of a heavy duty battery and an energy storage capacitor.

WIRING THE SYSTEM

CAUTION:If you do not feel comfortable with wiring your new unit, please see your local Authorized Rockford Fosgate Dealer for installation.

CAUTION:Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

CAUTION:Avoid running power wires near the low level input cables, antenna, power leads, sensitive equipment or harnesses.The power wires carry substantial current and could induce noise into the audio system.

1.Plan the wire routing. Keep RCA cables close together but isolated from the amplifier's power cables and any high power auto accessories, especially electric motors.This is done to prevent coupling the noise from radiated electrical fields into the audio signal.When feeding the wires through the firewall or any metal barrier, protect them with plastic or rubber grommets to prevent short circuits. Leave the wires long at this point to adjust for a precise fit at a later time.

NOTE:We recommend a 4 AWG wire for use on the power (B+) and ground (GND) connections.

2.Prepare the RED wire (power cable) for attachment to the amplifier by stripping 5/8" of insulation from the end of the wire. Insert the bared wire into the B+ terminal and tighten the set screw to secure the cable in place.

NOTE:The B+ cable MUST be fused 18" or less from the vehicle's battery. Install the fuseholder under the hood and ensure connections are water tight.

3. Trim the RED wire (power cable) within 18" of the battery and splice in a inline fuse holder (not supplied). See Specifications for the rating of the fuse to be used. DO NOT install the fuse at this time.

4.Strip 1/2" from the battery end of the power cable and crimp a

large ring terminal to the cable. Use the ring terminal to connect to the battery positive terminal.

6

Page 5 Page 7
Page 6
Image 6
Rockford Fosgate p3002 manual Installation Mounting Locations, Battery and Charging, Wiring the System
Page 5 Page 7

p3002 specifications

The Rockford Fosgate P3002 is a high-performance two-channel amplifier that stands out in the competitive world of car audio systems. Renowned for its power and sound quality, this amplifier is designed to deliver robust performance for both casual listeners and audiophiles alike.

One of the key features of the P3002 is its compact size. Measuring just 9.25 inches in width, it can easily fit in tight spaces without compromising the audio output. Designed with versatility in mind, it can be used to power a pair of speakers or an entire sound system. The amplifier offers a power output of 50 watts RMS per channel at 4 ohms, and it can deliver 75 watts RMS per channel at 2 ohms. This flexible power rating allows users to choose the ideal configuration for their specific audio setup.

The P3002 integrates advanced technologies that enhance both performance and reliability. One standout feature is the built-in thermal protection circuit, which ensures that the amplifier operates efficiently even under high load conditions. This helps prevent damage from overheating, prolonging the amplifier’s lifespan. Additionally, it includes short-circuit and over-voltage protection, making it a reliable choice for car audio systems.

Sound quality is paramount, and the P3002 does not disappoint. It features high and low-pass crossover settings, allowing users to tailor their sound experience. This flexibility lets audiophiles focus on their preferred frequencies, whether they want deep bass or crisp highs. Furthermore, with a signal-to-noise ratio of 80dB, it minimizes unwanted noise and distortion, ensuring a clean and powerful audio experience.

Durability is another hallmark of the P3002, with a chassis designed to withstand the rigors of daily use. Its sleek silver finish not only enhances aesthetics but also promotes heat dissipation. The amplifier’s RCA inputs make integration with factory systems straightforward, providing versatility for installation.

With a perfect combination of features, technologies, and characteristics, the Rockford Fosgate P3002 amplifier is a compelling choice for anyone looking to enhance their car audio experience. Its strong build quality, impressive power output, and sound customization options make it a standout in its category. Whether you’re a casual listener or a serious enthusiast, the P3002 is designed to elevate your music enjoyment on the road.
Top Page Image Contents