INSTALLATION

5.Prepare the BLACK wire (Ground cable) for attachment to the amplifier by stripping 5/8" of insulation from the end of the wire. Insert the bare wire into the GROUND terminal and tighten the set screw to secure the cable in place. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the other end of the wire and attach a ring connector. Fasten the cable to the chassis using a

non-anodized screw and a star washer.

NOTE:Keep the length of the BLACK wire (Ground) as short as possible.Always less than 30"(76.2cm).

6.Prepare the Remote turn-on wire for for attachment to the amplifier by stripping 5/8" of insulation from the end of the wire. Insert the bared wire into the REMOTE terminal and tighten the set screw to secure the wire in place. Connect the other end of the Remote wire to a switched 12 volt positive source.The switched voltage is usually taken from the source unit's remote amp on lead. If the source unit does not have this output available, the recommended solution is to wire a mechanical switch in line with a 12 volt source to activate the amplifier.

7.Securely mount the amplifier to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or plastic panels. Doing so may enable the screws to pull out from the panel due to road vibration or sudden vehicle stops.

8.Connect from source signal by plugging the RCA cables into the input jacks at the amplifier.

CAUTION:Always ensure power is off or disconnected at the amplifier before connecting RCA cables. Failure to do so may cause injury, damage to the amplifier and/or connected components.

9.Connect the speakers. Strip the speaker wires 1/2" and insert into the speaker terminal and tighten the set screw to secure into place. Be sure to maintain proper speaker polarity. DO NOT chassis ground any of the speaker leads as unstable operation may result.

10.Perform a final check of the completed system wiring to ensure that all connections are accurate. Check all power and ground connections for frayed wires and loose connections which could cause problems. Install inline fuse near battery connection.

NOTE:Follow the diagrams for

Power

proper signal polarity.

 

Connection

See Specifications for Fuse Rating

OR

P200-2

INPUT

P400-2

 

P300-2

P500-2

PASS-THRU

Bridged/

Mono Wiring

INPUT

7

Page 6 Page 8
Page 7
Image 7
Rockford Fosgate p3002 manual Installation, Connection, Bridged Mono Wiring
Page 6 Page 8

p3002 specifications

The Rockford Fosgate P3002 is a high-performance two-channel amplifier that stands out in the competitive world of car audio systems. Renowned for its power and sound quality, this amplifier is designed to deliver robust performance for both casual listeners and audiophiles alike.

One of the key features of the P3002 is its compact size. Measuring just 9.25 inches in width, it can easily fit in tight spaces without compromising the audio output. Designed with versatility in mind, it can be used to power a pair of speakers or an entire sound system. The amplifier offers a power output of 50 watts RMS per channel at 4 ohms, and it can deliver 75 watts RMS per channel at 2 ohms. This flexible power rating allows users to choose the ideal configuration for their specific audio setup.

The P3002 integrates advanced technologies that enhance both performance and reliability. One standout feature is the built-in thermal protection circuit, which ensures that the amplifier operates efficiently even under high load conditions. This helps prevent damage from overheating, prolonging the amplifier’s lifespan. Additionally, it includes short-circuit and over-voltage protection, making it a reliable choice for car audio systems.

Sound quality is paramount, and the P3002 does not disappoint. It features high and low-pass crossover settings, allowing users to tailor their sound experience. This flexibility lets audiophiles focus on their preferred frequencies, whether they want deep bass or crisp highs. Furthermore, with a signal-to-noise ratio of 80dB, it minimizes unwanted noise and distortion, ensuring a clean and powerful audio experience.

Durability is another hallmark of the P3002, with a chassis designed to withstand the rigors of daily use. Its sleek silver finish not only enhances aesthetics but also promotes heat dissipation. The amplifier’s RCA inputs make integration with factory systems straightforward, providing versatility for installation.

With a perfect combination of features, technologies, and characteristics, the Rockford Fosgate P3002 amplifier is a compelling choice for anyone looking to enhance their car audio experience. Its strong build quality, impressive power output, and sound customization options make it a standout in its category. Whether you’re a casual listener or a serious enthusiast, the P3002 is designed to elevate your music enjoyment on the road.
Top Page Image Contents