DESIGN FEATURES

12.RCA Input Jacks –The industry standard RCA jacks provide an easy connection for signal level input. They are nickel-plated to resist the signal degradation caused by corrosion.

13.REM Terminal –The heavy duty,nickel-plated captive c-clamp wire connector will accept wire sizes from 12 AWG to 24 AWG.This terminal is used to remotely turn-on and turn-off the amplifier when +12V DC is applied.

14.Power Terminals –The power and ground are nickel-plated captive c-clamp wire connectors and will accommodate up to 4 AWG wire.

INSTALLATION

INSTALLATION CONSIDERATIONS

The following is a list of tools needed for installation:

Fuse-holder and fuse.

(See specifications for fuse rating)

Volt/Ohm Meter

Wire strippers

Wire crimpers

Wire cutters

#2 Phillips screwdriver

Battery post wrench

Hand held drill w/assorted bits

1/8" diameter heatshrink tubing

Assorted connectors

Adequate Length—Red Power Wire

Adequate Length—Remote Turn-on Wire

Adequate Length—Black Grounding Wire

NOTE:We recommend a 4 AWG wire for use on the power (B+) and ground (GND) connections.

This section focuses on some of the vehicle considerations for installing your new amplifier. Pre-planning your system layout and best wiring routes will save installation time.When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments.

CAUTION:If you feel unsure about installing this system yourself, have it installed by a qualified technician.

CAUTION:Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

Before beginning any installation, follow these simple rules:

1.Be sure to carefully read and understand the instructions before attempting to install the unit.

2.For safety, disconnect the negative lead from the battery prior to beginning the installation.

3.For easier assembly, we suggest you run all wires prior to mounting your unit in place.

4.Route all of the RCA cables close together and away from any high current wires.

5.Use high quality connectors for a reliable installation and to minimize signal or power loss.

6.Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

7.Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.

8.Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

9.ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power wire within 18" (45.7 cm) of the battery terminal.

10.When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle.

5

Page 4 Page 6
Page 5
Image 5
Rockford Fosgate p3002 manual Installation Installation Considerations
Page 4 Page 6

p3002 specifications

The Rockford Fosgate P3002 is a high-performance two-channel amplifier that stands out in the competitive world of car audio systems. Renowned for its power and sound quality, this amplifier is designed to deliver robust performance for both casual listeners and audiophiles alike.

One of the key features of the P3002 is its compact size. Measuring just 9.25 inches in width, it can easily fit in tight spaces without compromising the audio output. Designed with versatility in mind, it can be used to power a pair of speakers or an entire sound system. The amplifier offers a power output of 50 watts RMS per channel at 4 ohms, and it can deliver 75 watts RMS per channel at 2 ohms. This flexible power rating allows users to choose the ideal configuration for their specific audio setup.

The P3002 integrates advanced technologies that enhance both performance and reliability. One standout feature is the built-in thermal protection circuit, which ensures that the amplifier operates efficiently even under high load conditions. This helps prevent damage from overheating, prolonging the amplifier’s lifespan. Additionally, it includes short-circuit and over-voltage protection, making it a reliable choice for car audio systems.

Sound quality is paramount, and the P3002 does not disappoint. It features high and low-pass crossover settings, allowing users to tailor their sound experience. This flexibility lets audiophiles focus on their preferred frequencies, whether they want deep bass or crisp highs. Furthermore, with a signal-to-noise ratio of 80dB, it minimizes unwanted noise and distortion, ensuring a clean and powerful audio experience.

Durability is another hallmark of the P3002, with a chassis designed to withstand the rigors of daily use. Its sleek silver finish not only enhances aesthetics but also promotes heat dissipation. The amplifier’s RCA inputs make integration with factory systems straightforward, providing versatility for installation.

With a perfect combination of features, technologies, and characteristics, the Rockford Fosgate P3002 amplifier is a compelling choice for anyone looking to enhance their car audio experience. Its strong build quality, impressive power output, and sound customization options make it a standout in its category. Whether you’re a casual listener or a serious enthusiast, the P3002 is designed to elevate your music enjoyment on the road.
Top Page Image Contents