Roland FP-2 Changing the Equalizer Settings, Connecting to Audio Equipment, Connection Examples

Chapter 4 Other Functions

Changing the Equalizer Settings

You can make fine, detailed changes to the equalizer settings.

1.Switch to Function mode (p. 38), and press the [Equalizer] button.

2.Hold down the [Equalizer] button, and press the [-] or [+] button to select item.

3.Press the [-] or [+] button to change the settings.

Param	Indi-	Value	Description
eter	cation
Low	Lo.G	-12–+12dB	Adjusts the level of the low-
Gain			frequency range.
Low	Lo.f	100, 200, 400	Frequency point in the low-
Freq		(Hz)	frequency range. Generally,
			this changes the level at and
			below this frequency.
Low	Lm.G	-12–+12dB	Adjusts the level of the low-
Mid			frequency range to
Gain			midrange.
Low	Lm.F	200, 250, 315,	Frequency point in the low-
Mid		400, 500, 630,	frequency range to
Freq		800, 1.00, 1.25,	midrange. This changes the
		1.60, 2.00, 2.50,	level of the specified band-
		3.15, 4.00, 5.00,	width centered on this fre-
		6.30, 8.00	quency.
Low	Lm.q	0.5, 1.0, 2.0,	Changes the bandwidth of
Mid		4.0, 8.0	the low-frequency range to
Q			midrange. The bandwidth
			affected by the controls nar-
			rows as the value increases.
High	Hm.G	-12–+12dB	Adjusts the level of the mid-
Mid			to high-frequency range.
Gain
High	Hm.F	200, 250, 315,	Frequency point in the mid-
Mid		400, 500, 630,	to high-frequency range to
Freq		800, 1.00, 1.25,	midrange. This changes the
		1.60, 2.00, 2.50,	level of the specified band-
		3.15, 4.00, 5.00,	width centered on this fre-
		6.30, 8.00	quency.
High	Hm.q	0.5, 1.0, 2.0,	Changes the bandwidth of
Mid		4.0, 8.0	the mid- to high-frequency
Q			range. The bandwidth
			affected by the controls nar-
			rows as the value increases.

Param	Indi-	Value	Description
eter	cation
High	Hi.G	-12–+12dB	Adjusts the level of the high-
Gain			frequency range.
High	Hi.F	2.00, 4.00, 8.00	Frequency point in the high-
Freq		(KHz)	frequency range. Generally,
			this changes the level at and
			over this frequency.

* Sounds may become distorted as the Gain level increases.

→The equalizer is switched on whenever the settings are changed.

→The FP-2 remembers the settings even while its power is turned off.

Connecting to Audio

Equipment

You can connect audio devices to play the sound of the FP-2 through the speakers of your audio system, or to record your performance on a tape recorder or other recording device.

When connecting, please use an audio cable with a standard phone plug (sold separately).

Connection Examples

*To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections.

Playing the sound of the FP-2 through the speakers of an audio system/Recording the performance of the FP-2 on a recording device

fig.audio1.e

Input R/L

(Line In, Aux In)

FP-2

❍Use the following procedure when turning on the power.

1.Set the volume of the FP-2 and of the connected devices to the minimum position.

2.Set the speaker switch to “Off” located on the rear panel.

3.Turn on the power of the FP-2.

4.Turn on the power of the connected device.

5.Adjust the volume of each device.

44