70

Effects List

Specifications for each Speaker Type

The speaker column indicates the diameter of each speaker unit (in

inches) and the number of units.

Flattens out high levels and boosts low levels, smoothing out

fluctuations in volume.

fig.MFX-40

Compresses signals that exceed a specified volume level, preventing

distortion from occurring.

fig.MFX-41

Cuts the reverb’s delay according to the volume of the sound sent into

the effect. Use this when you want to create an artificial-sounding

decrease in the reverb’s decay.

fig.MFX-42

Type Cabinet Speak-

er

Micro-

phone

SMALL 1

small open-back enclosure 10 dynamic

SMALL 2

small open-back enclosure 10 dynamic

MIDDLE

open back enclosure 12 x 1 dynamic

JC-120

open back enclosure 12 x 2 dynamic

BUILT-IN 1

open back enclosure 12 x 2 dynamic

BUILT-IN 2

open back enclosure 12 x 2 condenser

BUILT-IN 3

open back enclosure 12 x 2 condenser

BUILT-IN 4

open back enclosure 12 x 2 condenser

BUILT-IN 5

open back enclosure 12 x 2 condenser

BG STACK 1

sealed enclosure 12 x 2 condenser

BG STACK 2

large sealed enclosure 12 x 2 condenser

MS STACK 1

large sealed enclosure 12 x 4 condenser

MS STACK 2

large sealed enclosure 12 x 4 condenser

METAL STACK

large double stack 12 x 4 condenser

2-STACK

large double stack 12 x 4 condenser

3-STACK

large triple stack 12 x 4 condenser

40: COMPRESSOR

Parameter Value Description

Attack

0–127 Sets the speed at which compression starts

Threshold

0–127 Adjusts the volume at which compression
begins

Post Gain

0– +18 dB Adjusts the output gain.

Low Gain

-15– +15 dB Gain of the low frequency range

High Gain

-15– +15 dB Gain of the high frequency range

Level

0–127 Output level
L in
R in
L out
R out

Compressor

2-Band EQ
2-Band EQ

Compressor

41: LIMITER

Parameter Value Description

Release

0–127
Adjusts the time after the signal volume falls
below the Threshold Level until compression
is no longer applied.

Threshold

0–127 Adjusts the volume at which compression
begins

Ratio

1.5:1, 2:1,
4:1,
100:1
Compression ratio

Post Gain

0– +18 dB Adjusts the output gain.

Low Gain

-15– +15 dB Gain of the low frequency range

High Gain

-15– +15 dB Gain of the high frequency range

Level

0–127 Output level

42: GATE

Parameter Value Description

Threshold

0–127
Volume level at which the gate begins to close

Mode

GATE,
DUCK
Type of gate
GATE:
The gate will close when the vol-
ume of the original sound decreases, cut-
ting the original sound.
DUCK (Ducking):
The gate will close when
the volume of the original sound increas-
es, cutting the original sound.

Attack

0–127 Adjusts the time it takes for the gate to fully
open after being triggered.

Hold

0–127
Adjusts the time it takes for the gate to start
closing after the source sound falls beneath
the Threshold.

Release

0–127 Adjusts the time it takes the gate to fully
close after the hold time.

Balance

D100:0W–
D0:100W
Volume balance between the direct sound
(D) and the effect sound (W)

Level

0–127 Output level
L in
R in
L out
R out

Limiter

2-Band EQ
2-Band EQ

Limiter

L in
R in
L out
R out

Gate

Gate

GW-8_e.book 70 ページ 2008年4月1日 火曜日 午前11時44分