Rotel RDV-995 owner manual RR-DV92 Remote Control

Connecting the Power Cord

AC Input

Your RDV-995 is configured at the factory for the proper AC line voltage in the country where you purchased it (USA: 115 volts/60Hz AC or CE: 230 volts/50Hz AC). The AC line configuration is noted on a decal on the back of your unit.

After all the audio/video connections have been made, plug the supplied power cord into the AC INPUT receptacle on the back of the unit. Then insert the power plug into an AC wall outlet. The STANDBY indicator lights and setup is complete. Note that a small amount of power (3 watts) is always used while the power cord is connected to the wall outlet.

Observe the following precautions:

• Do not connect or disconnect the power cord

with wet hands.

• Disconnect the power cord if you are not

going to use the unit for a long time.

• When unplugging the player from the wall

outlet, always pull the plug, not the power

cord.

• Disconnect the power cord before clean-

ing the unit.

• Disconnect the power cord before moving

the unit.

• Do not damage, alter, twist, or pull the power

cord, as this may damage the cord and

cause fire, electric shock, or other accidents.

Contact a dealer and get a new power cord

if the cord is damaged.

• Do not put anything heavy, on the unit, or

the power cord, as this may cause fire, elec-

9

2Place the two accessory R6P (SUM-3)/AA(15F)

batteries in the remote control according to the polarity markings (“+” and “–”) inside the compartment and on the batteries.

3 Place the cover over the com- partment, and press down lightly.

The batteries will last about six months with normal use. If the functions of the remote control become erratic, replace the batteries.

Precautions for the safe use of batteries

Observe the following precautions for the safe use of batteries. If they are used improperly their life will be shortened, they may burst or their contents may leak.

•Remove the batteries from the remote control if it is not going to be used for a long pe- riod of time.

•Remove dead batteries and dispose of them properly.

•Never leave dead batteries lying around, take them apart, mix them with other refuse, or throw them into an incinerator.

•Never touch liquid that has leaked out of a battery.

•Do not mix new and old batteries, or bat- teries of different types, when replacing them.

			English
No.	Manufacturer
01	JVC	09	Zenith
02	Magnavox	10	Hitachi
03	Mitsubishi	11	Panasonic
04	Panasonic	12	Samsung
05	RCA	13	Sanyo
06	Sharp	14	Sanyo
07	Sony	15	Samsung
08	Toshiba

2Press the STOP 25 button, then release the TV/VIDEO button.

3Test the program setting by pressing the TV POWER 15 button to see if it turns your set on. If there is more than one code listed for the manufacturer of your TV, try them one by one until you succeed.

Remote Control TV Operation

The following buttons can be used for oper- ating the TV (The numbers in brackets are those shown on figure 1 on page 3.)

TV POWER 15

Turns the TV on or off when the SHIFT 7 button is also pressed.

TV CH 18

Changes the TV channels.

TV VOL 19

Adjusts the TV volume.

0 - 9 (Numeric Buttons) 5

Selects the TV channels (while holding down the SHIFT button). Note: For some TVs, pressing “+10” while holding down SHIFT functions as the “+100”. “+10” functions as ENTER if your TV requires pressing the ENTER after select- ing a channel number.

TV/VIDEO 16

Switches input mode (either TV or VIDEO).

tric shock, or other accidents.

RR-DV92 Remote Control

Installing the Batteries

The battery compartment is located on the back of the remote control unit.

1Press down on the point shown by the ar- row at the top of the compartment cover,

and pull up the cover to open the compart- ment.

Programming the RR-DV92 Remote to Control a TV

You can operate your TV from the remote control unit. The remote must first be pro- grammed to operate your TV set.

1 Press and hold down the TV/VIDEO 16 button. Then enter the manufacturer code of your TV listed in the next column using the numeric buttons (0 - 9) 5 . Do not re- lease TV/VIDEO. Keep holding it until the next step is completed. (Example: To enter code “01” press and release the “0” but- ton, then press and release the “1” button.

External Remote In

The 3.5mm mini-jack (labeled EXT REM IN) receives command signals from an industry standard infrared receiver. This feature is useful when the unit is installed in a cabinet and the front panel sensor is blocked. Consult your authorized Rotel dealer for information on external receivers and the proper wiring of a jack to fit the mini-jack receptacle.

NOTE: The IR signals from the External Remote In jack can be relayed to source components using IR emitters or hardwired connections from the IR Out jacks.