RSDX-02eDVD Receiver

20

Volume Adjustments

The listening volume of the RSDX-02e can be adjusted from the front panel or the remote.

Front Panel: Rotate the front panel VOLUME control clockwise to increase the volume, coun- terclockwise to decrease.

Remote: Press the VOL UP hard button to in- crease the volume; press the VOL DOWN hard button to decrease.

When you adjust the volume, the setting is shown on the front panel display.

Muting the Sound

The volume of the RSDX-02e can be temporarily turned off or muted. Push the MUTE command on the remote once to mute the sound. The word MUTING appears in the front panel display. Press the MUTE command again to restore pre- vious volume levels.

NOTE: Adjusting the VOLUME controls on ei- ther the front panel or the remote also restores the volume when the RSDX-02e is muted.

Changing Display Brightness

P2-C

There are two brightness settings for the front panel display. Press the DIMMER command on Page 2 of the remote to toggle between the bright and dim display settings.

Selecting Source Inputs

Up to six source components, including the built- in DVD player and FM/AM tuner, can be se- lected for listening and/or viewing with the RSDX-02e. Selecting a source input can be done from the front panel or the remote control.

Selecting an Input from the Front Panel

To select an input source from the front panel, press any of the six input selector buttons. The name of the selected input appears in the front panel display.

NOTE: When the TAPE/CDR button is pressed, either TAPE or CDR appears in the front panel, depending on which name is assigned to the input. See Changing Input Name below.

Selecting an Input from the Remote

To select an input from the remote control, push any of the input source commands on Page 1 or Page 2.

Four of the inputs (DVD, STB, TV, CDR) are available on Page 1 of the remote screens. An additional three inputs (FM/AM, TAPE, VCR) are available on Page 2.

The name of the selected source appears in the front panel display.

NOTE: Either the TAPE or the CDR input is avail- able depending on which name has been assigned to the input. See Changing Input Name below.

Changing Input Name

The TAPE/CDR inputs can be used for a CDR (compact disc recorder) or TAPE (analog tape recorder). The correct name (TAPE or CDR) should be correctly assigned to these inputs so that the name appears in the display, so that the INPUT buttons on the remote work as expected, and so that digital inputs are avail- able for use with a CDR. As delivered from the factory, the RSDX-02e has the TAPE name assigned to these inputs. To change the input name to CDR:

1.Select the TAPE/CDR inputs by pressing the TAPE/CDR input button.

2.Press and hold the TAPE/CDR button until the words ASSIGN. CDR appear in the front panel display.

To change the input name back to TAPE, re- peat Step 2, holding the button until ASSIGN. TAPE appears in the display.

Selecting Digital

or Analog Inputs P6-C

A digital source component can be connected to the RSDX-02e using either for digital or ana- log cables, allowing the selection of the digi- tal or analog signal for an input. There are two available modes:

DIGITAL AUTO: The selection of digital or analog inputs is automatic. If a digital signal is available for the selected input, the RSDX-02e uses it. If a digital signal is not available, the RSDX-02e will use the analog signal.

ANALOG: The RSDX-02e uses the analog signal, even if a digital signal is available.

By default, all of the inputs (except the DVD input) are set at the factory for the ANALOG mode. To change the mode:

1.Select the desired input by pressing an INPUT select button on the front panel or remote.

2.Press the INPUT AG/DG button on the front panel or ANG/DIG command on Page 6 of the remote control to change the mode. The selected mode, either ANALOG or DGTL AUTO is shown in the front panel display.

NOTE: The built-in DVD input always uses digi- tal signals and cannot be changed. This set- ting is memorized independently for all other digital inputs.

Selecting the Digital Signal

P6-D

When the DIGITAL AUTO mode is selected and a digital signal is detected, one of four indicators appears in the display, depending on the type of digital signal being received:

DOLBY DIGITAL: Dolby Digital signal is being received.

DTS: DTS signal is being received.

LPCM: Linear PCM signal (such as a CD) is being received.

PPCM: DVD AUDIO Packed PCM digital sig- nal is being received.

In almost all cases, the correct type of digital signal is detected and decoded automatically in DIGITAL AUTO mode. However, when us- ing the DVD input, you can manually force the RSDX-02e into either Dolby Digital or DTS modes if necessary.

From the front panel:

1.While using the DVD input, press the front panel INPUT AG/DG button or ANG/DIG command on Page 6 of the remote to change the mode so that DGTL AUTO is shown in the front panel display.

2.While DGTL AUTO is displayed, press the

CONTROL buttons on the front panel to step through the three options: DGTL AUTO, DGTL D.D, and DGTL DTS.

Page 20
Image 20
Rotel RSDX-02e Volume Adjustments, Muting the Sound, Changing Display Brightness, Selecting an Input from the Front Panel