Installation

Wall Port Installation

1.Pick an unobtrusive location close to the controller that all cables (speaker and keypad) can be routed to.

2.Install an electrical box, using a UL/CSA approved plastic single-gang (18 ci or deeper) electrical box. If there will be two controllers you should use two single-gang boxes separated slightly to allow space for the cables.

3.Route CAT-5 wire from the electrical box to the four keypad locations. Route the speaker cable from the electrical box to the corresponding speaker locations. Label each set of cables with the zone and location.

4.Terminate each CAT-5 wire with a RJ-45 plug using the T568A standard configuration.

5.Strip 1 to 2 inches (2.5 to 5 cm) off the end of each speaker cable jacket.

Then strip 1/4 inch (0.7 cm) of insulation off each wire.

6.Twist the speaker wire strands together so there are no strands separated from the bundle.

7.Insert the proper speaker wire, matching channel and polarity for all four wires. Tighten the screws until the wires are secured in the terminal. Cable as follows (standard 4-conductor):

White -- L+ (left channel positive) Green -- L- (left channel negative) Black -- R- (right channel negative) Red -- R+ (right channel positive)

8.Check to make sure there are no stray strands of wire outside the terminals. If there are, remove the wire, twist the strands together, and reconnect the wire to the terminal.

9.Complete the same steps for the remaining zones. Plug each of the RJ-45 plugs into the corresponding keypad zone jack on the rear of the wall port. Note: All four connections from the controller to the wall port must be made, even if there are less than 4 keypads connected to the system. Cables between the wall port and the controller must match numerically (#1 on the wall port to #1 on the controller).

10.Mount the wall port in the electrical box. Push any extra cable back into the wall. Screw the wall port plate to the electrical box. Attach the trim plate to the wall port.

Speaker Outputs

The CA4 supports speaker outputs for zones 1 through 4 for each controller with a maximum of eight zones. Each speaker connection requires a 8-ohm load and will provide 15 watts per channel. Standard 16-gauge 4-conductor stranded speaker wire can be run up to 125 feet; 14-gauge wire can be run up to 250 feet.

The speakers are connected to the CA4 Wall Port using fixed screw terminals. Each of these terminals is designated for the speaker set of a particular amplified zone. To avoid confusion, connect one zone speaker set at a time starting with Zone 1, taking care to keep zone and speaker wire identities straight.

/

/

/

/

14

Russound CA4 System Installation Manual

Page 14
Image 14
Russound CA4 installation manual Wall Port Installation, Speaker Outputs

CA4 specifications

The Russound CA4 is an advanced multi-room audio system designed to deliver high-quality sound throughout the home. As a versatile and user-friendly solution for audiophiles and casual listeners alike, the CA4 caters to the growing demand for integrated entertainment experiences in today's smart homes.

One of the main features of the Russound CA4 is its ability to distribute audio to multiple zones, allowing users to enjoy different sources and adjust volumes independently in each area of the house. With the support for up to four zones, the CA4 is perfect for a medium-sized home. The system can seamlessly integrate with a variety of audio sources, including local streaming services, FM radio, and external devices such as CD players and gaming consoles, making it easy for users to enjoy their favorite content.

The CA4 employs advanced technologies to ensure superior sound quality and reliable performance. Utilizing high-resolution audio support, it reproduces music with pristine clarity, bringing out the details in every track. The Russound CA4 also features a sophisticated digital signal processor (DSP) that optimizes sound distribution, allowing it to adapt to various environments and speaker configurations. This ensures that listeners experience consistent audio quality, no matter where they are in the house.

One of the standout characteristics of the CA4 is its user-friendly interface. The system can be controlled through various methods, including an intuitive mobile app, dedicated wall controls, or remote controls. This flexibility allows users to manage their audio experience from anywhere in the house, making it easier to adjust settings or switch sources on the fly.

Moreover, the CA4 features compatibility with popular smart home platforms, enabling voice control and automation capabilities. This integration allows for seamless operation with existing home automation systems, making it a highly adaptable choice for modern smart homes.

Overall, the Russound CA4 embodies a blend of quality, functionality, and ease of use, making it a stellar choice for anyone wanting to enhance their home audio setup. With its robust feature set and commitment to delivering an exceptional listening experience, the CA4 represents a significant advancement in multi-room audio technologies. Whether hosting a gathering or enjoying a quiet evening, the Russound CA4 ensures that high-quality sound is always within reach.