OPERATION

WARNING:

Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to comply with ANSI Z87.1, along with hearing protection. Failure to do so could result in objects being thrown into your eyes and other possible serious injuries.

WARNING:

Never use blades, flailing devices, wire, or rope on this product. Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.

FUELING AND REFUELING the trimmer

Clean the surface around the fuel cap to prevent contamination.

Loosen the fuel cap slowly by turning counter­ clockwise.

Pour the fuel carefully into the tank.

Cleanand inspect the fuel cap gasket before replacing the fuel cap.

Replace the fuel cap and tighten it by turning it clockwise.

Wipe spilled fuel from the product.

Move at least 30 ft. away from refueling area before starting the product.

NOTE: It is normal for smoke to be emitted from a new engine after first use.

Ethanol. Gasoline containing up to 10% ethanol by volume (commonly referred to as E10) or 15% ethanol by volume (commonly referred to as E15) are acceptable. E85 is not.

CAUTION:

Attempting to start the engine before it has been properly filled with lubricant will result in equipment failure.

ADDING/checking engine lubricant

See Figure 8.

Enginelubricant has a major influence on engine perfor- mance and service life. This unit is shipped with a 20W50 engine lubricant to assist in the break-in period. For best operating performance, continuing to use 20W50 engine lubricant is recommended, however, SAE 30, 10W30, or 10W40 are all acceptable lubricants to use in this product. Always use a 4-stroke motor lubricant that meets or exceeds the requirements for API service classification SJ. Check lubricant level before each use.

NOTE: Non-detergent or 2-stroke engine lubricants will damage the engine and should not be used.

To add engine lubricant:

Remove the cap and seal from lubricant bottle

provided­ .

Unscrew the oil cap/dipstick and remove.

Using the funnel provided, add one entire bottle of engine lubricant through oil fill hole.

Reinstall the oil cap/dipstick and secure.

To check engine lubricant level:

Place unit on a flat surface.

Wipe dipstick clean and re-seat in hole; do not rethread.

Remove dipstick again and check lubricant level. Lubricant level should fall within the hatched area on the dipstick.

If level is low, add engine lubricant until the fluid level rises to the upper portion of the hatched area on the dipstick.

Replace and secure the oil cap/dipstick.

WARNING:

Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. from refueling site before starting engine. Do not smoke and stay away from open flames and sparks. Failure to safely handle fuel could result in serious per- sonal injury.

OXYGENATED FUELS

DO NOT USE E85 FUEL. IT WILL VOID YOUR WAR- RANTY.

NOTE: Fuel system damage or performance problems re- sulting from the use of an oxygenated fuel containing more than the percentages of oxygenates stated below are not covered under warranty.

caution:

Do not overfill. Overfilling the crankcase may cause ­excessive smoke, oil loss, and engine damage.

STARTING AND STOPPING

See Figures 9 - 12.

To start an engine that is cold or has run dry:

nPlace the on/stop switch in the ON (  ) position.

NOTE: Do not engage the throttle lever during the start- ing process.

Press the primer bulb 10 times slowly.

Set start lever to start position.

Stand beside the trimmer and place your right hand on the handlebar and your foot on the frame as shown.

8 — English

Page 12
Image 12
Ryobi RY13010 Operation, Fueling and Refueling the trimmer, ADDING/checking engine lubricant, Oxygenated Fuels