Operation

BASIC OPERATION OF THE TABLE SAW

A table saw can be used for straight-line cutting operations such as cross cutting, ripping, mitering, beveling, and com- pound cutting. It can dado with optional accessories.

The 3-prong plug must be plugged into a matching outlet that is properly installed and grounded according to all local codes and ordinances. Improper connection of the equip- ment can result in electric shock. Check with an electrician or service personnel if you are unsure about proper grounding. Do not modify the plug; if it will not fit the outlet, have the correct outlet installed by a qualified electrician. Refer to the Electrical page of this manual.

Note: This table saw is designed to cut wood and wood composition products only.

CAUSES OF KICKBACK

Kickback can occur when the blade stalls or binds, kicking the workpiece back toward you with great force and speed. If your hands are near the saw blade, they may be jerked loose from the workpiece and may contact the blade. Obvi- ously, kickback can cause serious injury, and it is well worth using precautions to avoid the risks.

Kickback can be caused by any action that pinches the blade in the wood, such as the following:

Making a cut with incorrect blade depth

Sawing into knots or nails in the workpiece

Twisting the wood while making a cut

Failing to support work

Forcing a cut

Cutting warped or wet lumber

Using the wrong blade for the type of cut

Not following correct operating procedures

Misusing the saw

Failing to use the anti-kickback pawls

Cutting with a dull, gummed-up, or improperly set blade

AVOIDING KICKBACK

Always use the correct blade depth setting. The top of the blade teeth should clear the workpiece by 1/8 in. to 1/4 in.

Inspect the work for knots or nails before beginning a cut. Knock out any loose knots with a hammer. Never saw into a loose knot or nail.

Always use the rip fence when rip cutting and the miter gauge when cross cutting. This helps prevent twisting the wood in the cut.

Always use clean, sharp, and properly-set blades. Never make cuts with dull blades.

To avoid pinching the blade, support the work properly before beginning a cut.

When making a cut, use steady, even pressure. Never force cuts.

Do not cut wet or warped lumber.

Always hold your workpiece firmly with both hands or with pushsticks. Keep your body in a balanced position to be ready to resist kickback should it occur. Never stand directly in line with the blade.

Use the right type of blade for the cut being made.

Use the blade guard assembly for all through cuts.

CUTTING AIDS

See Figure 18.

Pushsticks are devices used for safely pushing a workpiece through the blade instead of using your hands. They can be made in various sizes and shapes from scrap wood to use in a specific project. The stick must be narrower than the workpiece, with a 90˚ notch in one end and shaping for a grip on the other end.

A pushblock has a handle fastened by recessed screws from the underside. Use it on non-through cuts.

CAUTION:

Be sure the screw is recessed to avoid damaging the saw or workpiece.

PUSHSTICKS

PUSHBLOCKS

Fig. 18

WARNING:

Never stand directly in line with the blade or allow hands to come closer than 3 in. to the blade. Do not reach over or across the blade. Failure to heed this warning can result in serious personal injury.

CUTTING TIPS

Dado and rabbet cuts are non-through cuts which can be either rip cuts or cross cuts. Carefully read and understand all sections of this operator’s manual before attempting any operation.

WARNING:

All blades and dado sets must be rated for at least 5,500 RPM to prevent possible injury.

Page 20

Table Saw specifications

The Ryobi Table Saw is a powerful and versatile tool designed for both hobbyists and professional woodworkers. Known for its durability and efficiency, this table saw is an essential addition to any workshop. One of its standout features is the high-performance motor, which typically operates at 15 amps, delivering ample power to handle a variety of cutting tasks with ease. This ensures that it can cut through hardwood, softwood, and even plywood without bogging down.

A notable characteristic of the Ryobi Table Saw is its precision. Equipped with a robust aluminum table, the saw offers a flat, sturdy surface that promotes accurate cuts. The table is typically expansive, allowing users to work on larger materials without difficulty. With the inclusion of rack and pinion fence system, users can make quick adjustments to the blade position, ensuring that each cut is clean and precise. The fence system is user-friendly, allowing for smooth adjustments with minimal effort.

Safety is a top priority in Ryobi's design, and this is reflected in various features like the blade guard and anti-kickback pawls. The blade guard provides visibility of the cut line while protecting the user from potential injury. Additionally, the saw often includes a push stick, which helps maintain a safe distance from the blade during operation.

Another key technology found in the Ryobi Table Saw is its portability. Many models are designed to be lightweight and feature wheels, making it easy to move the saw from one location to another. This is particularly advantageous for contractors or those who have limited workshop space.

Dust collection is also an important aspect of woodworking, and the Ryobi Table Saw typically includes a built-in dust port. This enables users to connect a shop vac or dust collector, minimizing the mess and ensuring a cleaner work environment.

In summary, the Ryobi Table Saw integrates powerful performance with user-friendly features. Its precision cutting capabilities, safety mechanisms, and portability make it an excellent tool for anyone looking to tackle woodworking projects. Whether you're a seasoned professional or a DIY enthusiast, the Ryobi Table Saw can elevate your craftsmanship and improve your woodworking efficiency.

Ryobi Table Saw manual Operation

Models: Table Saw

OPERATION