BASIC OPTIONS
3. | Installing remote controls |
|
|
|
|
|
|
|
|
|
|
3.1 | Key Chain Remote Control KR21 |
|
|
|
|
|
|
|
|
|
|
1. | CONTROLE INDICATOR |
|
|
|
|
|
|
|
|
|
|
| Lights up when the remote control transmits radio signals when | 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| pressing the buttons. If the indicator light is not very bright, the |
|
|
|
|
|
|
|
|
|
|
2. | batteries should be replaced. | 2 |
|
|
|
|
|
| 3 | ||
|
|
|
|
|
| ||||||
ARM |
|
|
|
|
|
|
|
|
|
| |
| Switches on the alarm in Arm Away mode (all sensors activated). |
|
|
|
|
|
|
|
|
|
|
3. | DISARM | 4 |
|
|
|
|
|
|
|
| 5 |
| Switches off the security system. |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |
4. | LIGHTS ON |
|
|
|
|
|
|
|
| 9 |
|
| Switches on your light modules (7.5). |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |
5. | LIGHTS OFF | 7 |
|
|
|
|
|
|
|
| 8 |
7+8. | Switches off your light modules (7.5). |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| ||
PANIC |
|
|
|
|
|
|
|
|
|
| |
| If the (red) buttons 7 and 8 are pressed together, the panic alarm is |
|
|
|
|
|
|
|
|
|
|
| activated (6.2). |
|
|
|
|
|
|
|
|
|
|
9.BATTERY COMPARTMENT
The battery compartment can be found in the remote control.
3.1.1 Using the Key Chain Remote Control
1.BATTERIES
A new KR21 contains fully charged batteries.
2.ACTIVATING THE KR21.
Keep the ARM button on your remote control pressed for 4 seconds. Release the button. The remote control has now chosen a unique code, which can be registered with your console.
☺When pressing the ARM button the LED should flash quickly a few times. When the LED lights up and stays lit, you need to reactivate the KR21
3.1.2 Registering the Key Chain Remote Control
1.To access the menu, press the menu or menu button. The display will now read ‘ENTER PIN’.
2.Enter your
3.When the PIN code has been entered correctly, the word ‘INSTALL’ will show up on the display.
4.Press OK. The display now reads ‘INSTALL ZONE’.
5.Press the ARM button on your key chain remote control. The console will beep to confirm. The display will read ‘RMOT 1 SET’.
☺If you have more than 1 remote control installed, it will read e.g. RMOT 2 SET, RMOT 3 SET, … RMOT 16 SET. You can register up to 16 remote controls.
6.Repeat step 5 for every remote control you wish to register.
7.Press CLEAR to go back to the main menu. Press CLEAR again to quit the menu. To confirm your choice, press 1 for Yes or 2 for No. If you choose Yes, you will quit the menu. If you choose No, you go back to the main menu.
☺You can also remove remote controls from the menu, e.g. when you have lost a remote control. This method is described in 8.2.
☺Read chapter 12 for information on replacing the batteries..
12 | MARMITEK |