Manuals / Samson / Home Audio / Stereo Amplifier

Samson S63, S83 manual Mixer, Amplifier, Samson, S83 / S63

Models: S63, S83 S83

1 29

Download 29 pages 5.84 Kb

Page 1

Image 1

MIXER

AMPLIFIER

SAMSON®

S83 / S63

Page 1

Image 1

Samson S63, S83 manual Mixer, Amplifier, Samson, S83 / S63

Contents

AMPLIFIER MIXERSAMSON S83 / S63Introduction S83/S63 Features Guided Tour - S83 Introduction S83/S63 Features A phantom power switch enables you to use the S83 and S63 with high- quality condenser microphones. When turned on, 48 volts of phantom power is provided to the mic connectors of all input channels S83/S63 FeaturesPOWER Guided Tour - S83 OverviewChannels Main SectionGuided Tour - S83 Channel 1 2 Guided Tour - S83 Main Section6 10 7 Guided Tour - S83 Main Section output signal. At the fully clockwise “+10” position, approximately 10 db of gain is being added by the mixer to the output signal. For more information, see the “Setting Up and Using the S83/S63” section in this manualGuided Tour - S83 Rear Panel Guided Tour - S83 Rear Panel 5 Amp In - This unbalanced input allows you to connect any external mono- phonic line-levelsignal directly to the S83 power amplifier. This input is not affected by either the ten-bandgraphic master equalizer or the S83’s Main Level control. The Amp In jack can optionally also be used as an insert patch point as followsChannels Guided Tour - S63 OverviewMain Section S6 MIXER AMPLIFIERGuided Tour - S63 Channel Guided Tour - S63 Main Section Guided Tour - S63 Main Section 4 Ten-BandGraphic Master EQ - These sliders allow you to add ±15 db of boost or attenuation to ten different frequency areas, affecting the main output signal of the S63. When a slider is at its center detented “0 db” position, the selected frequency area is unaffected it is said to be flat. When a slider is moved up above the “0 db” position, towards the “+15 db” position, the selected frequency area is boosted, and when it is moved down below the “0 db” posi- tion, towards the “-15db” position, the selected frequency area is being attenu- ated. For more information, see the “Using Equalization” section in this manualGuided Tour - S63 Rear Panel Guided Tour - S63 Rear Panel 5:Amp In - This unbalanced input allows you to connect any external mono- phonic line-levelsignal directly to the S63 power amplifier. This input is not affected by either the ten-bandgraphic master equalizer or the S63’s Main Level control. The Amp In jack can optionally also be used as an insert patch point as follows+ SIGNAL Connecting The S83/S63 - General Suggestions+ SIGNAL 3 - SIGNAL 1 GROUND TO MIXER 2 + SIGNALSetting Up and Using the S83/S63 Setting the Correct Gain Structure PM EST Setting the Correct Gain StructureSuggested Performance Application - S83 Suggested Performance Application - S63 Grounding Techniques S83 EQ section Using EqualizationTen-bandgraphic master equalizer S63 EQ sectionuntil the ringing or feedback disappears. Don’t lower the frequency area any further than you need to, or the quality of the overall sound may suffer. If you don’t specifically need to utilize the ten-bandgraphic master equalizer in a partic- ular environment, leave it completely flat all sliders at their center detented “0” position Using EqualizationEffects Send knobs Using The Effects Sends and ReturnsEffects Send jacks S83 Effects Return jacksUsing the Monitor Output Using the Monitor Output and Internal ReverbUsing the Internal Reverb Monitor output jackPower Amp Section SpecificationsMixer / Pre Amp Section General