Step 4.3 Performing final check and trial operation

1Check the following:

•Strength of the installation site

•Tightness of pipe connection to detect gas leak

•Electric wiring connection

•Heat-resistant insulation of the pipe

•Drainage

•Grounding conductor connection

•Correct operation (Take the following steps.)

2Press the (Power) button on the remote control to check the following:

•The indicator on the indoor unit lights up.

•The airflow blade opens and the fan gears up for operation.

3Press the (Mode) button to select Cool or Heat mode. Then take the following sub-steps:

•In Cool mode, use the Temperature button to set the set temperature to 16 °C.

•In Heat mode, use the Temperature button to set the set temperature to 30 °C.

•Check whether, approximately 3 to 5 minutes later, the outdoor unit starts, and a cool air blows out.

•After12 minutes of stationary condition, check the indoor unit air treatment.

4Press the (Air swing) button to check whether the airflow blades work properly.

5Press the (Power) button to stop the trial operation.

Pumping down for removing the product

Pump-down is an operation intended to collect all the system refrigerant in the outdoor unit. This operation must be carried out before disconnecting the refrigerant tubing in order to avoid refrigerant loss to the atmosphere.

WARNING

•After installing the product, be sure to perform leak tests on the piping connections. After pumping down refrigerant to inspect or relocate the outdoor unit, be sure to stop the compressor and then remove the connected pipes.

–– Do not operate the compressor while a valve is open due to refrigerant leakage from a pipe or an unconnected or incorrectly connected pipe. Failure to do so may cause air to flow into the compressor and too a high pressure to develop inside the refrigerant circuit, leading to an explosion or product malfunction.

1Hold down the (Power) button on the indoor unit for 5 seconds. Beep sounds immediately to indicate that the product is ready for pump down procedure.

2Let the compressor run for more than 5 minutes.

3Release the valve caps on High and Low pressure side.

4Use L-wrench to close the valve on the high pressure side.

5After approximately1 minute, close the valve on the low pressure side.

6Stop operation of the air conditioner by pressing the (Power) button on the indoor unit or remote control.

7Disconnect the pipes.

CAUTION

•Compressor damage may occur if the compressor is run at a negative suction pressure.

 

1

 

1 minute

Liquid service port

Gas service port

<High pressure>

<Low pressure>

2

Off

English 23

Installation

Page 22 Page 24
Page 23
Image 23
Samsung AR12MSPXBWKNEU Performing final check and trial operation, Check the following Strength of the installation site
Page 22 Page 24

AR09MSPXAWKXEU, AR12MSWXBWKNEU, AR12MSPXASIXEU, AR09MSPXASIXEU, AR07MSWXBWKNEU specifications

The Samsung AR09MSPXBWKNEU and its counterparts, the AR12MSPXBWKXEU, AR12MSPXBWKNEU, and AR09MSPXBWKXEU, are part of Samsung’s innovative range of air conditioning units designed for superior performance and energy efficiency. These models represent a combination of sleek design, advanced technology, and user-friendly features, catering to residential and commercial cooling needs.

One of the standout features of these units is their powerful inverter technology. This technology allows the air conditioner to automatically adjust its power based on the room's cooling needs, ensuring consistent temperature levels while minimizing energy consumption. As a result, users benefit from lower electricity bills and a reduced environmental footprint.

Another significant characteristic is the Triple Protector Plus technology. This feature enhances the durability of the units by providing protection against voltage fluctuations, operating without stabilizers, and preventing corrosion on the unit's surface. This ensures that the air conditioners can withstand varying weather conditions and are built to last longer.

The Wind-Free cooling technology further sets these models apart. It enables a comfortable environment by dispersing cool air through micro-holes, creating a gentle breeze without the uncomfortable direct airflow. This results in a more pleasant indoor climate and can contribute to better overall health and comfort for occupants.

In addition, the AR09MSPXBWKNEU and AR12MSPX series are equipped with a user-friendly Smart Things application that allows users to control their air conditioning units remotely. This capability offers convenience and flexibility, enabling scheduling, temperature adjustments, and even monitoring of energy consumption directly from a smartphone.

Furthermore, these models come with easy-to-clean filters that are washable, promoting better air quality by trapping dust and allergens, which can be particularly beneficial for individuals with allergies or respiratory conditions.

Lastly, the modern and minimalist design of the Samsung air conditioning units ensures that they seamlessly blend into any interior decor, making them not just functional appliances but also aesthetic additions to the space.

In summary, Samsung’s AR09MSPXBWKNEU, AR12MSPXBWKXEU, AR12MSPXBWKNEU, and AR09MSPXBWKXEU air conditioners showcase cutting-edge technology, robust features, and energy efficiency, making them excellent options for consumers looking to enhance their indoor climate conditions.
Top Page Image Contents