Samsung BN68-01783B-00 user manual Listening through a Receiver Home theater

Listening through a Receiver (Home theater)

You can listen to sound through a receiver instead of the
TV speaker.		View TV
1	Press the TOOLS button.
		Device List
2	Press the ENTER button to select Anynet+ (HDMI-CEC).	Recording : DVDR
	Press the ▲ or ▼ button to select Receiver.	DVDR Operation
	Press the ◄ or ► button to select On or Off.	Receiver	◄	On	►
3	Press the EXIT button to exit.	Setup

¯If your receiver supports audio only, it may not appear in

the device list. Move Adjust Return

¯The receiver will work when you have properly connected

the Optical IN jack of the receiver to the Optical Out jack of the TV.

¯When the receiver (home theater) is set to On, you can hear sound output from the TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.

¯When listening through the receiver, there are restrictions for using the PIP and audio-related menus.

¯If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power cord or a power failure), the Select Speaker may be set to External Speaker when you turn the TV on again. (see page 34)

Check Points before Requesting Service

Symptom	Solution
Anynet+ does not work.	■ Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+
	devices only.
	■ Connect only one receiver.
	■ Check if the Anynet+ device power cord is properly connected.
	■ Check the Anynet+ device’s Video/Audio/HDMI cable connections.
	■ Check whether Anynet+ (HDMI-CEC)is set to On in the Anynet+ setup menu.
	■ Check whether the TV remote control is in TV mode.
	■ Check whether it is Anynet+ exclusive remote control.
	■ Anynet+ doesn’t work at a certain condition. (Searching channels)
	■ When connecting or removing the HDMI cable, please make sure to search devices
	again or restart your TV.
	■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+.	■ Check if the Anynet+ device is properly connected to the TV and check if the Anynet+
	(HDMI-CEC)is set to On in the Anynet+ Setup menu.
	■ Press the TV button on the TV remote control to switch to TV. Then press the TOOLS
	button to show the Anynet+ menu and select a menu you want.
I want to exit Anynet+.	■ Select View TV in Anynet+ menu.
	■ Press the SOURCE button on the TV remote control and select a device other than
	Anynet+ devices.
	■ Press any of CH, CH LIST, and PRE-CHto change to the TV mode.
	(Note that the channel button operates only when a tuner-embedded Anynet+ device
	is not connected.)
The message Connecting	■ You cannot use the remote control when you are configuring Anynet+ or switching to a
to Anynet+ device…	view mode.
appears on the screen.	■ Use the remote control when the Anynet+ setting or switching to view mode is complete.
The Anynet+ device does	■ You cannot use the play function when Plug & Play is in progress.
not play.
The connected device is	■ Check whether or not the device supports Anynet+ functions.
not displayed.	■ Check whether or not the HDMI cable is properly connected.
	■ Check whether Anynet+ (HDMI-CEC)is set to On in the Anynet+ setup menu.
	■ Search Anynet+ devices again.
	■ You can connect an Anynet+ device using the HDMI cable only. Some HDMI cables
	may not support Anynet+ functions.
The TV programme cannot	■ Check whether the antenna jack on the recording device is properly connected.
be recorded.
The TV sound is not output	■ Connect the optical cable between TV and the receiver.
through the receiver.
	English - 69