Samsung DCS-816 FIGURE 3-1

SAMSUNG Installation

DCS-816 March 1999

3-1

PART 3. INSTALLING OPTION CARDS AND TRUNK CARDS (Figure 3-1)

Unpack and inspect each card before installing. Check for signs of physical damage. If any

damage is detected, do not attempt to install. Contact the local distributor for advice immediately.

The DCS-816 system has one (1) trunk expansion slot for a trunk card and two (2) option

connections for SIO and AA. See Figure 3-1.

INSTALLING OPTION CARDS AND A TRUNK CARD

FIGURE 3-1

Technical Manuals Online! - http://www.tech-man.com

Contents

Main Page i Table of Contents PART 3. INSTALLING OPTION CARDS AND TRUNK CARDS (FIGURE 3-1).............. 3-1 PART 4. POWER-UP PROCEDURE ..4-1 PART 5. CONNECTING PSTN CIRCUITS ..5-1 PART 6. CONNECTING STATION EQUIPMENT ...6-1 PART 8. CHANGING SOFTWARE (FIGURE 8-1)8-1 FIGURES PART 1. SITE REQUIREMENTS Page PART 2. INSTALLING THE BASIC KSU 2.1 SYSTEM CONFIGURATION AND CAPACITY FIGURE 2-1 2.4 GROUNDING THE KSU (Figure 2-2) 2.5 MDF CABLING (Figure 2-3) FIGURE 2-2 GROUNDING THE KSU 2-4 Details of Champ Connections Pin Colour Circuits/ Functions Remark Details of RJ-45 Connections Pin No. Circuits/ Functions Remarks FIGURE 2-3 MDF CABLING BOTTOM VIEW FRONT VIEW AFTER REMOVING THE FRONT COVER 2.6 External Battery Connection (Figure 2-4) FIGURE 2-4 CONNECTING A SYSTEM BACKUP BATTERY Page SELECTING OPTIONS ON THE BASIC KSU FIGURE 2-5 FIGURE 3-1 3.1 SIO1 Option Card (Figure 3-2) 3.2 AA Option Card (Figure 3-2) FIGURE 3-2 SIO1 OPTION CARD AND AA OPTION CARD 3.3 8TRK Card (Figure 3-3) 3.4 2/4BRI Card (Figure 3-3) 8TRK CARD AND 2/4BRI CARD FIGURE 3-3 3.5 4TRK Card (Figure 3-4) FIGURE 3-4 4TRK CARD PART 4. POWER-UP PROCEDURE 4.1 Connect Power to the System (Figures 4-1 and 4-2) Page 4.2 Monitor LED Indication and Memory Backup Selection 4.3 PCB Verification 4.4 Default Trunk and Station Numbering Page PART 5. CONNECTING PSTN CIRCUITS 5.1 Safety Precautions 5.2 Loop-start Lines (Figure 5-1) FIGURE 5-1 PSTN (C.O.) Loop-Start Lines CONNECTING LOOP-START LINES 5.3 Off Premise Extension (OPX) (Figure 5-2) FIGURE 5-2 CONNECTING OPX LINES Long Line Extension 5.4 ISDN BRI Lines (Figure 5-3) CONNECTING BRI LINES FIGURE 5-3 ISDN BRI Lines PART 6. CONNECTING STATION EQUIPMENT 6.1 Safety Precautions 6.2 Digital Keysets (Figure 6-1) CONNECTING DIGITAL KEYSETS FIGURE 6-1 6.3 Single Line Telephones (Figure 6-2) CONNECTING SINGLE LINE TELEPHONES FIGURE 6-2 6.4 Door Phone and Door Lock Release (Figure 6-3) CONNECTING A DOOR PHONE AND LOCK RELEASE FIGURE 6-3 6.5 CTM - CTI Module (TAPI) (Figure 6-4) CONNECTING A CTM (TAPI) FIGURE 6-4 6.6 ISDN TE (ISDN phone, G4 FAX, etc) (Figure 6-5) CONNECTING ISDN TE FIGURE 6-5 PART 7. CONNECTING OPTIONAL EQUIPMENT 7.1 Music-on-Hold / Background Music (Figure 7-1) CONNECTING EXTERNAL MUSIC FIGURE 7-1 7.2 External Paging (Figure 7-2) CONNECTING EXTERNAL PAGING EQUIPMENT FIGURE 7-2 7.3 Common Bell (Figure 7-3) CONNECTING AN EXTERNAL LOUD BELL FIGURE 7-3 7.4 Ring Over Page 7.5 Station Message Detail Recording (SMDR) (Figure 7-4) PIN CONNECTIONS TO PRINTER FIGURE 7-4 SIO BOARD (DTE DB9) PRINTER (DTE DB25) 7.6 PC Programming (Figure 7-5) PIN CONNECTIONS TO PC FIGURE 7-5 SIO BOARD (DTE DB9) PC (DTE DB25 or DB9) 7.7 Remote Programming (Figure 7-6) 7.8 Power Failure Transfer PIN CONNECTIONS TO MODEM FIGURE 7-6 SIO BOARD (DTE DB9) MODEM (DCE DB25) 7.9 Voice Mail / Auto Attendant (Figure 7-7) CONNECTING VM/AA FIGURE 7-7 7.10 Information on DCS-816 Serial Interface (Figure 7-8) INFORMATION ON SERIAL INTERFACE FIGURE 7-8 SIO BOARD (DTE DB9) PART 8. CHANGING SOFTWARE (Figure 8-1) CHANGING SOFTWARE FIGURE 8-1