Samsung DCS-816 FIGURE 6-4

SAMSUNG Installation

DCS-816 March 1999

6-5

6.5 CTM - CTI Module (TAPI) (Figure 6-4)

The DCS CTM module is required to support CTI (TAPI) in the system. The CTM has a DLI

connection and a personal computer (PC) interface, which can be connected to any DLI port of

DCS-816. The system requires MDF connection for CTM modules and modular jack connection

for a keyset. A PC may connect to the module via the DB9 connector. See Figure 2-3 and refer

to section 2.5 (MDF Cabling).

Using one pair twisted wires, connect each CTM module (via the modular jack marked ‘DLI IN’) to

the DLI port of your choice via the champ connector on the base board and then connect the

module (via the other modular jack marked ‘KTS OUT’) to a keyset. A PC can be connected to

the module via the DB9 connector.

A special PC software package is required to run CTI (TAPI) and how to set up the software is

described in the other document in detail. Contact your dealer for information.

CONNECTING A CTM (TAPI)

25 PAIR CABLE WITH FEMALE CONNECTOR TO THE BASE CHAMP CONNECTOR

FIGURE 6-4

CHAMP CONNECTION

PIN COLOUR CIRCUITS / FUNCTIONS

39/14 BK-BR/ BR/BK T/R, 1

st

DLI port on base

40/15 BK-S/ S-BK T/R, 2nd DLI port on base

41/16 Y-BL/ BL-Y T/R, 3rd DLI port on base

42/17 Y-O/ O-Y T/R, 4th DLI port on base

43/18 Y-GR/ GR-Y T/R, 5th DLI port on base

44/19 Y-BR/ BR-Y T/R, 6th DLI port on base

45/20 Y-S/ S-Y T/R, 7th DLI port on base

46/21 VL-BL/BL-VL T/R, 8th DLI port on base

47/22 VL-O/ O-VL T/R, 9th DLI port on base

48/23 VL-GR/ GR-VL T/R, 10th DLI port on base

49/24 VL-BR/ BR-VL T/R, 11th DLI port on base

50/25 VL-S/ S-VL T/R, 12th DLI port on base

² CONNECT A CTM TO ANY DLI PORT

² YOU CANNOT INSTALL THE EQUIPMENT

OUTDOORS

² SPECIAL PC SOFTWARE REQUIRED

¡¡

CT£Í

¡¡ ¡¡¡¡ ¡¡ ¡¡¡¡

£Ð£Ã

COM 1 CO M 2

TXD 2 2 3 (Rx D )

RXD 3 3 OR 2 (Tx D )

GND 5 5 7 (GN D )

9 PIN 25 PIN

PI N A S S I G N M EN T

DLI

¡¤

IN

RS-232-C(DB-9) KTS

¡¤

OUT

3 4

Technical Manuals Online! - http://www.tech-man.com

Contents

Main Page i Table of Contents PART 3. INSTALLING OPTION CARDS AND TRUNK CARDS (FIGURE 3-1).............. 3-1 PART 4. POWER-UP PROCEDURE ..4-1 PART 5. CONNECTING PSTN CIRCUITS ..5-1 PART 6. CONNECTING STATION EQUIPMENT ...6-1 PART 8. CHANGING SOFTWARE (FIGURE 8-1)8-1 FIGURES PART 1. SITE REQUIREMENTS Page PART 2. INSTALLING THE BASIC KSU 2.1 SYSTEM CONFIGURATION AND CAPACITY FIGURE 2-1 2.4 GROUNDING THE KSU (Figure 2-2) 2.5 MDF CABLING (Figure 2-3) FIGURE 2-2 GROUNDING THE KSU 2-4 Details of Champ Connections Pin Colour Circuits/ Functions Remark Details of RJ-45 Connections Pin No. Circuits/ Functions Remarks FIGURE 2-3 MDF CABLING BOTTOM VIEW FRONT VIEW AFTER REMOVING THE FRONT COVER 2.6 External Battery Connection (Figure 2-4) FIGURE 2-4 CONNECTING A SYSTEM BACKUP BATTERY Page SELECTING OPTIONS ON THE BASIC KSU FIGURE 2-5 FIGURE 3-1 3.1 SIO1 Option Card (Figure 3-2) 3.2 AA Option Card (Figure 3-2) FIGURE 3-2 SIO1 OPTION CARD AND AA OPTION CARD 3.3 8TRK Card (Figure 3-3) 3.4 2/4BRI Card (Figure 3-3) 8TRK CARD AND 2/4BRI CARD FIGURE 3-3 3.5 4TRK Card (Figure 3-4) FIGURE 3-4 4TRK CARD PART 4. POWER-UP PROCEDURE 4.1 Connect Power to the System (Figures 4-1 and 4-2) Page 4.2 Monitor LED Indication and Memory Backup Selection 4.3 PCB Verification 4.4 Default Trunk and Station Numbering Page PART 5. CONNECTING PSTN CIRCUITS 5.1 Safety Precautions 5.2 Loop-start Lines (Figure 5-1) FIGURE 5-1 PSTN (C.O.) Loop-Start Lines CONNECTING LOOP-START LINES 5.3 Off Premise Extension (OPX) (Figure 5-2) FIGURE 5-2 CONNECTING OPX LINES Long Line Extension 5.4 ISDN BRI Lines (Figure 5-3) CONNECTING BRI LINES FIGURE 5-3 ISDN BRI Lines PART 6. CONNECTING STATION EQUIPMENT 6.1 Safety Precautions 6.2 Digital Keysets (Figure 6-1) CONNECTING DIGITAL KEYSETS FIGURE 6-1 6.3 Single Line Telephones (Figure 6-2) CONNECTING SINGLE LINE TELEPHONES FIGURE 6-2 6.4 Door Phone and Door Lock Release (Figure 6-3) CONNECTING A DOOR PHONE AND LOCK RELEASE FIGURE 6-3 6.5 CTM - CTI Module (TAPI) (Figure 6-4) CONNECTING A CTM (TAPI) FIGURE 6-4 6.6 ISDN TE (ISDN phone, G4 FAX, etc) (Figure 6-5) CONNECTING ISDN TE FIGURE 6-5 PART 7. CONNECTING OPTIONAL EQUIPMENT 7.1 Music-on-Hold / Background Music (Figure 7-1) CONNECTING EXTERNAL MUSIC FIGURE 7-1 7.2 External Paging (Figure 7-2) CONNECTING EXTERNAL PAGING EQUIPMENT FIGURE 7-2 7.3 Common Bell (Figure 7-3) CONNECTING AN EXTERNAL LOUD BELL FIGURE 7-3 7.4 Ring Over Page 7.5 Station Message Detail Recording (SMDR) (Figure 7-4) PIN CONNECTIONS TO PRINTER FIGURE 7-4 SIO BOARD (DTE DB9) PRINTER (DTE DB25) 7.6 PC Programming (Figure 7-5) PIN CONNECTIONS TO PC FIGURE 7-5 SIO BOARD (DTE DB9) PC (DTE DB25 or DB9) 7.7 Remote Programming (Figure 7-6) 7.8 Power Failure Transfer PIN CONNECTIONS TO MODEM FIGURE 7-6 SIO BOARD (DTE DB9) MODEM (DCE DB25) 7.9 Voice Mail / Auto Attendant (Figure 7-7) CONNECTING VM/AA FIGURE 7-7 7.10 Information on DCS-816 Serial Interface (Figure 7-8) INFORMATION ON SERIAL INTERFACE FIGURE 7-8 SIO BOARD (DTE DB9) PART 8. CHANGING SOFTWARE (Figure 8-1) CHANGING SOFTWARE FIGURE 8-1