Manuals / Brands / Communications / Telephone / Samsung / Communications / Telephone

Samsung DCS-816 4.2 Monitor LED Indication and Memory Backup Selection, 4.3 PCB Verification, 4.4 Default Trunk and Station Numbering

1 43

Download 43 pages, 1.26 Mb

SAMSUNG Installation

DCS-816 March 1999

4-3

4.2 Monitor LED Indication and Memory Backup Selection

After verifying proper operation of the power supply, turn your system ON to check the operation

of the monitor LED on the base board. The LED should flicker rapidly indicating the main

processor is functioning.

Now move the Memory Backup Selector to the ON position (Figure 2-5). Failure to do so may

result in a loss of programming data and customer data in the event of a power failure.

4.3 PCB Verification

Before connecting all MDF cabling, plug in a test cable to the Champ connector on the base board

(Figure 2-3). Connect a display set and verify that it is working.

Use maintenance program MMC 727 (System Version Display) to verify the system version and

software version and to confirm the status of installed cards. Otherwise, please contact your

dealer for advice.

Remove the test cable and plug in an amphenol-type cable and an RJ-45 cable to the MDF.

Proceed with the rest of the installation.

4.4 Default Trunk and Station Numbering

At the beginning of system operation the CPU reads the expansion slot and the option connections

for the presence of a card and identifies the type. It stores this as the default configuration.

The system assigns trunk numbers beginning with 701. Station numbers begins with 201. The

keyset connected to the lowest port is assigned to the operator by default and all incoming trunk

calls ring the station until the default data is changed by programming.

Station and trunk numbers can be changed, rearranged and reassigned as needed using program

MMC 724 (Dial Numbering Plan).

Technical Manuals Online! - http://www.tech-man.com

Contents

Main Page i Table of Contents PART 3. INSTALLING OPTION CARDS AND TRUNK CARDS (FIGURE 3-1).............. 3-1 PART 4. POWER-UP PROCEDURE ..4-1 PART 5. CONNECTING PSTN CIRCUITS ..5-1 PART 6. CONNECTING STATION EQUIPMENT ...6-1 PART 8. CHANGING SOFTWARE (FIGURE 8-1)8-1 FIGURES PART 1. SITE REQUIREMENTS Page PART 2. INSTALLING THE BASIC KSU 2.1 SYSTEM CONFIGURATION AND CAPACITY FIGURE 2-1 2.4 GROUNDING THE KSU (Figure 2-2) 2.5 MDF CABLING (Figure 2-3) FIGURE 2-2 GROUNDING THE KSU 2-4 Details of Champ Connections Pin Colour Circuits/ Functions Remark Details of RJ-45 Connections Pin No. Circuits/ Functions Remarks FIGURE 2-3 MDF CABLING BOTTOM VIEW FRONT VIEW AFTER REMOVING THE FRONT COVER 2.6 External Battery Connection (Figure 2-4) FIGURE 2-4 CONNECTING A SYSTEM BACKUP BATTERY Page SELECTING OPTIONS ON THE BASIC KSU FIGURE 2-5 FIGURE 3-1 3.1 SIO1 Option Card (Figure 3-2) 3.2 AA Option Card (Figure 3-2) FIGURE 3-2 SIO1 OPTION CARD AND AA OPTION CARD 3.3 8TRK Card (Figure 3-3) 3.4 2/4BRI Card (Figure 3-3) 8TRK CARD AND 2/4BRI CARD FIGURE 3-3 3.5 4TRK Card (Figure 3-4) FIGURE 3-4 4TRK CARD PART 4. POWER-UP PROCEDURE 4.1 Connect Power to the System (Figures 4-1 and 4-2) Page 4.2 Monitor LED Indication and Memory Backup Selection 4.3 PCB Verification 4.4 Default Trunk and Station Numbering Page PART 5. CONNECTING PSTN CIRCUITS 5.1 Safety Precautions 5.2 Loop-start Lines (Figure 5-1) FIGURE 5-1 PSTN (C.O.) Loop-Start Lines CONNECTING LOOP-START LINES 5.3 Off Premise Extension (OPX) (Figure 5-2) FIGURE 5-2 CONNECTING OPX LINES Long Line Extension 5.4 ISDN BRI Lines (Figure 5-3) CONNECTING BRI LINES FIGURE 5-3 ISDN BRI Lines PART 6. CONNECTING STATION EQUIPMENT 6.1 Safety Precautions 6.2 Digital Keysets (Figure 6-1) CONNECTING DIGITAL KEYSETS FIGURE 6-1 6.3 Single Line Telephones (Figure 6-2) CONNECTING SINGLE LINE TELEPHONES FIGURE 6-2 6.4 Door Phone and Door Lock Release (Figure 6-3) CONNECTING A DOOR PHONE AND LOCK RELEASE FIGURE 6-3 6.5 CTM - CTI Module (TAPI) (Figure 6-4) CONNECTING A CTM (TAPI) FIGURE 6-4 6.6 ISDN TE (ISDN phone, G4 FAX, etc) (Figure 6-5) CONNECTING ISDN TE FIGURE 6-5 PART 7. CONNECTING OPTIONAL EQUIPMENT 7.1 Music-on-Hold / Background Music (Figure 7-1) CONNECTING EXTERNAL MUSIC FIGURE 7-1 7.2 External Paging (Figure 7-2) CONNECTING EXTERNAL PAGING EQUIPMENT FIGURE 7-2 7.3 Common Bell (Figure 7-3) CONNECTING AN EXTERNAL LOUD BELL FIGURE 7-3 7.4 Ring Over Page 7.5 Station Message Detail Recording (SMDR) (Figure 7-4) PIN CONNECTIONS TO PRINTER FIGURE 7-4 SIO BOARD (DTE DB9) PRINTER (DTE DB25) 7.6 PC Programming (Figure 7-5) PIN CONNECTIONS TO PC FIGURE 7-5 SIO BOARD (DTE DB9) PC (DTE DB25 or DB9) 7.7 Remote Programming (Figure 7-6) 7.8 Power Failure Transfer PIN CONNECTIONS TO MODEM FIGURE 7-6 SIO BOARD (DTE DB9) MODEM (DCE DB25) 7.9 Voice Mail / Auto Attendant (Figure 7-7) CONNECTING VM/AA FIGURE 7-7 7.10 Information on DCS-816 Serial Interface (Figure 7-8) INFORMATION ON SERIAL INTERFACE FIGURE 7-8 SIO BOARD (DTE DB9) PART 8. CHANGING SOFTWARE (Figure 8-1) CHANGING SOFTWARE FIGURE 8-1