Samsung DCS-816 FIGURE 5-1

SAMSUNG Installation

DCS-816 March 1999

5-2

5.2 Loop-start Lines (Figure 5-1)

The DCS-816 system requires MDF connection for analogue trunk (loop-start) lines. The Basic

KSU itself is equipped with two analogue trunk lines. Additionally, a 4TRK or an 8TRK card can be

installed in the trunk expansion slot. All connections for loop-start lines can be done through the

champ connector on the base board. See Figure 2-3 and refer to section 2.5 (MDF Cabling).

Use one pair twisted wires and connect each loop-start C.O. line to the trunk port you choose via

the champ connector on the base board.

FIGURE 5-1

CHAMP CONNECTION

PIN COLOUR CIRCUITS / FUNCTIONS

26/ 1 W-BL/ BL-W T/R, 1

st

Trunk on base board

27/ 2 W-O/ O-W T/R, 2nd Trunk on base board

28/ 3 W-GR/ GR-W T/R, 1st Trunk on 4/8TRK

29/ 4 W-BR/ BR-W T/R, 2nd Trunk on 4/8TRK

30/ 5 W-S/ S-W T/R, 3rd Trunk on 4/8TRK

31/ 6 R-BL/ BL-R T/R, 4th Trunk on 4/8TRK

32/ 7 R-O/ O-R T/R, 5th Trunk on 8TRK

33/ 8 R-GR/ GR-R T/R, 6th Trunk on 8TRK

34/ 9 R-BR/ BR-R T/R, 7th Trunk on 8TRK

35/10 R-S/ S-R T/R, 8th Trunk on 8TRK

25 PAIR CABLE WITH FEMALE CONNECTOR TO THE BASE CHAMP CONNECTOR

PSTN (C.O.)

Loop-Start

Lines

² NO POLARITY

² 2 LOOP-START LINES TO THE BASIC KSU.

THESE LINES WILL BE TRANSFERRED TO STN

15 AND STN 16 IN CASE OF POWER FAILURE

² 4 OR 8 ADDITIONAL LOOP-START LINES

IF A 4TRK OR AN 8TRK CARD IS INSTALLED

CONNECTING LOOP-START LINES

Technical Manuals Online! - http://www.tech-man.com

Contents

Main Page i Table of Contents PART 3. INSTALLING OPTION CARDS AND TRUNK CARDS (FIGURE 3-1).............. 3-1 PART 4. POWER-UP PROCEDURE ..4-1 PART 5. CONNECTING PSTN CIRCUITS ..5-1 PART 6. CONNECTING STATION EQUIPMENT ...6-1 PART 8. CHANGING SOFTWARE (FIGURE 8-1)8-1 FIGURES PART 1. SITE REQUIREMENTS Page PART 2. INSTALLING THE BASIC KSU 2.1 SYSTEM CONFIGURATION AND CAPACITY FIGURE 2-1 2.4 GROUNDING THE KSU (Figure 2-2) 2.5 MDF CABLING (Figure 2-3) FIGURE 2-2 GROUNDING THE KSU 2-4 Details of Champ Connections Pin Colour Circuits/ Functions Remark Details of RJ-45 Connections Pin No. Circuits/ Functions Remarks FIGURE 2-3 MDF CABLING BOTTOM VIEW FRONT VIEW AFTER REMOVING THE FRONT COVER 2.6 External Battery Connection (Figure 2-4) FIGURE 2-4 CONNECTING A SYSTEM BACKUP BATTERY Page SELECTING OPTIONS ON THE BASIC KSU FIGURE 2-5 FIGURE 3-1 3.1 SIO1 Option Card (Figure 3-2) 3.2 AA Option Card (Figure 3-2) FIGURE 3-2 SIO1 OPTION CARD AND AA OPTION CARD 3.3 8TRK Card (Figure 3-3) 3.4 2/4BRI Card (Figure 3-3) 8TRK CARD AND 2/4BRI CARD FIGURE 3-3 3.5 4TRK Card (Figure 3-4) FIGURE 3-4 4TRK CARD PART 4. POWER-UP PROCEDURE 4.1 Connect Power to the System (Figures 4-1 and 4-2) Page 4.2 Monitor LED Indication and Memory Backup Selection 4.3 PCB Verification 4.4 Default Trunk and Station Numbering Page PART 5. CONNECTING PSTN CIRCUITS 5.1 Safety Precautions 5.2 Loop-start Lines (Figure 5-1) FIGURE 5-1 PSTN (C.O.) Loop-Start Lines CONNECTING LOOP-START LINES 5.3 Off Premise Extension (OPX) (Figure 5-2) FIGURE 5-2 CONNECTING OPX LINES Long Line Extension 5.4 ISDN BRI Lines (Figure 5-3) CONNECTING BRI LINES FIGURE 5-3 ISDN BRI Lines PART 6. CONNECTING STATION EQUIPMENT 6.1 Safety Precautions 6.2 Digital Keysets (Figure 6-1) CONNECTING DIGITAL KEYSETS FIGURE 6-1 6.3 Single Line Telephones (Figure 6-2) CONNECTING SINGLE LINE TELEPHONES FIGURE 6-2 6.4 Door Phone and Door Lock Release (Figure 6-3) CONNECTING A DOOR PHONE AND LOCK RELEASE FIGURE 6-3 6.5 CTM - CTI Module (TAPI) (Figure 6-4) CONNECTING A CTM (TAPI) FIGURE 6-4 6.6 ISDN TE (ISDN phone, G4 FAX, etc) (Figure 6-5) CONNECTING ISDN TE FIGURE 6-5 PART 7. CONNECTING OPTIONAL EQUIPMENT 7.1 Music-on-Hold / Background Music (Figure 7-1) CONNECTING EXTERNAL MUSIC FIGURE 7-1 7.2 External Paging (Figure 7-2) CONNECTING EXTERNAL PAGING EQUIPMENT FIGURE 7-2 7.3 Common Bell (Figure 7-3) CONNECTING AN EXTERNAL LOUD BELL FIGURE 7-3 7.4 Ring Over Page 7.5 Station Message Detail Recording (SMDR) (Figure 7-4) PIN CONNECTIONS TO PRINTER FIGURE 7-4 SIO BOARD (DTE DB9) PRINTER (DTE DB25) 7.6 PC Programming (Figure 7-5) PIN CONNECTIONS TO PC FIGURE 7-5 SIO BOARD (DTE DB9) PC (DTE DB25 or DB9) 7.7 Remote Programming (Figure 7-6) 7.8 Power Failure Transfer PIN CONNECTIONS TO MODEM FIGURE 7-6 SIO BOARD (DTE DB9) MODEM (DCE DB25) 7.9 Voice Mail / Auto Attendant (Figure 7-7) CONNECTING VM/AA FIGURE 7-7 7.10 Information on DCS-816 Serial Interface (Figure 7-8) INFORMATION ON SERIAL INTERFACE FIGURE 7-8 SIO BOARD (DTE DB9) PART 8. CHANGING SOFTWARE (Figure 8-1) CHANGING SOFTWARE FIGURE 8-1