Samsung DCS-816 FIGURE 3-4

SAMSUNG Installation

DCS-816 March 1999

3-4

3.5 4TRK Card (Figure 3-4)

Four (4) analogue trunk interfaces with MPD or PRS options

The card has four (4) interfaces for MPD or PRS option chips. Install any MPD or PRS chip before

installing the card. For PRS and 50Hz MPD facilities, the capacitors marked on Figure 3-4 should

be replaced with wire-jumpers. Install the card and ensure that it is fully inserted into the slot.

Some components are not mounted. Only one card per system.

FIGURE 3-4

MPD/PRS SOCKETS

FOR TRK1 TO TRK4

FROM THE TOP

2 CAPACITORS

PER PORT

4TRK CARD

Technical Manuals Online! - http://www.tech-man.com

Contents

Main Page i Table of Contents PART 3. INSTALLING OPTION CARDS AND TRUNK CARDS (FIGURE 3-1).............. 3-1 PART 4. POWER-UP PROCEDURE ..4-1 PART 5. CONNECTING PSTN CIRCUITS ..5-1 PART 6. CONNECTING STATION EQUIPMENT ...6-1 PART 8. CHANGING SOFTWARE (FIGURE 8-1)8-1 FIGURES PART 1. SITE REQUIREMENTS Page PART 2. INSTALLING THE BASIC KSU 2.1 SYSTEM CONFIGURATION AND CAPACITY FIGURE 2-1 2.4 GROUNDING THE KSU (Figure 2-2) 2.5 MDF CABLING (Figure 2-3) FIGURE 2-2 GROUNDING THE KSU 2-4 Details of Champ Connections Pin Colour Circuits/ Functions Remark Details of RJ-45 Connections Pin No. Circuits/ Functions Remarks FIGURE 2-3 MDF CABLING BOTTOM VIEW FRONT VIEW AFTER REMOVING THE FRONT COVER 2.6 External Battery Connection (Figure 2-4) FIGURE 2-4 CONNECTING A SYSTEM BACKUP BATTERY Page SELECTING OPTIONS ON THE BASIC KSU FIGURE 2-5 FIGURE 3-1 3.1 SIO1 Option Card (Figure 3-2) 3.2 AA Option Card (Figure 3-2) FIGURE 3-2 SIO1 OPTION CARD AND AA OPTION CARD 3.3 8TRK Card (Figure 3-3) 3.4 2/4BRI Card (Figure 3-3) 8TRK CARD AND 2/4BRI CARD FIGURE 3-3 3.5 4TRK Card (Figure 3-4) FIGURE 3-4 4TRK CARD PART 4. POWER-UP PROCEDURE 4.1 Connect Power to the System (Figures 4-1 and 4-2) Page 4.2 Monitor LED Indication and Memory Backup Selection 4.3 PCB Verification 4.4 Default Trunk and Station Numbering Page PART 5. CONNECTING PSTN CIRCUITS 5.1 Safety Precautions 5.2 Loop-start Lines (Figure 5-1) FIGURE 5-1 PSTN (C.O.) Loop-Start Lines CONNECTING LOOP-START LINES 5.3 Off Premise Extension (OPX) (Figure 5-2) FIGURE 5-2 CONNECTING OPX LINES Long Line Extension 5.4 ISDN BRI Lines (Figure 5-3) CONNECTING BRI LINES FIGURE 5-3 ISDN BRI Lines PART 6. CONNECTING STATION EQUIPMENT 6.1 Safety Precautions 6.2 Digital Keysets (Figure 6-1) CONNECTING DIGITAL KEYSETS FIGURE 6-1 6.3 Single Line Telephones (Figure 6-2) CONNECTING SINGLE LINE TELEPHONES FIGURE 6-2 6.4 Door Phone and Door Lock Release (Figure 6-3) CONNECTING A DOOR PHONE AND LOCK RELEASE FIGURE 6-3 6.5 CTM - CTI Module (TAPI) (Figure 6-4) CONNECTING A CTM (TAPI) FIGURE 6-4 6.6 ISDN TE (ISDN phone, G4 FAX, etc) (Figure 6-5) CONNECTING ISDN TE FIGURE 6-5 PART 7. CONNECTING OPTIONAL EQUIPMENT 7.1 Music-on-Hold / Background Music (Figure 7-1) CONNECTING EXTERNAL MUSIC FIGURE 7-1 7.2 External Paging (Figure 7-2) CONNECTING EXTERNAL PAGING EQUIPMENT FIGURE 7-2 7.3 Common Bell (Figure 7-3) CONNECTING AN EXTERNAL LOUD BELL FIGURE 7-3 7.4 Ring Over Page 7.5 Station Message Detail Recording (SMDR) (Figure 7-4) PIN CONNECTIONS TO PRINTER FIGURE 7-4 SIO BOARD (DTE DB9) PRINTER (DTE DB25) 7.6 PC Programming (Figure 7-5) PIN CONNECTIONS TO PC FIGURE 7-5 SIO BOARD (DTE DB9) PC (DTE DB25 or DB9) 7.7 Remote Programming (Figure 7-6) 7.8 Power Failure Transfer PIN CONNECTIONS TO MODEM FIGURE 7-6 SIO BOARD (DTE DB9) MODEM (DCE DB25) 7.9 Voice Mail / Auto Attendant (Figure 7-7) CONNECTING VM/AA FIGURE 7-7 7.10 Information on DCS-816 Serial Interface (Figure 7-8) INFORMATION ON SERIAL INTERFACE FIGURE 7-8 SIO BOARD (DTE DB9) PART 8. CHANGING SOFTWARE (Figure 8-1) CHANGING SOFTWARE FIGURE 8-1