Rear Panel View

B

 

1

 

2

 

3

DIGITAL OUT

 

OPTICAL

4

 

 

5

 

6

 

7

 

8

Where to Install Your

Mini-Compact System

To take full advantage of your new mini-compact system, fol- low these installation instructions before connecting the unit.

Install the system on a flat, stable surface.

Never place this unit on carpeting.

Never place this unit in an outdoor area.

Maintain an open space of approximately 6 inches (15 cm) on the sides and rear of the system, for ventilation purposes.

Make sure that you have enough room to open the compact disc compartment easily.

Place the loudspeakers at a reasonable distance on either side of the system to ensure good stereo sound.

Direct the loudspeakers towards the listening area.

For optimum performance, make sure that both speakers are placed at an equal distance above the floor.

Connecting the Loudspeakers

GB

The loudspeaker connector terminals are located on the rear of the system.

There are four terminals on the system:

Two for the left speaker (marked L)

Two for the right speaker (marked R)

To achieve the correct sound quality, connect the:

Red wire to the + terminals

Black wire to the – terminals

1

To connect a wire to a terminal, push the tab as far as it will go:

 

To the right on the system

2

Insert the wire, up to the plastic sheathing, in the hole.

3

Push the tab back:

 

To the left on the system, until it clicks into place

 

To the top on the loudspeaker

 

Result: The wire is pinched and held firmly in place.

4

Repeat the operation for each wire.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

(+)

(–)

(+)

(–)

( )

1.SUB WOOFER PRE OUT

2.VIDEO OUT

3.S-VIDEO OUT

4.DIGITAL OUT JACK

5.FM AERIAL CONNECTOR TERMINAL

6.AM AERIAL CONNECTOR TERMINAL

7.AUX INPUT

8.LINE OUT

9.LOUDSPEAKER CONNECTOR TERMINALS

Connecting your System to the Power Supply

The main lead must be plugged into an appropriate socket.

 

Before plugging your system into a main socket, you must check

 

the voltage.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Plug the main lead (marked AC Cord on the rear of the system) into

 

an appropriate socket.

2

Press the On/Standby button to switch your mini-compact system

 

on.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connection of the subwoofer (optional)

The subwoofer generates low-pitched tones.

(Ex. Explosion, the sound of spacecraft flying, the sound of pon- dering, etc.)

Connect the subwoofer (not supplied)

Connect the subwoofer cord to the SUBWOOFER IN and SUB WOOFER PRE OUT terminal.

Plug the AC Cord on the rear of the SUBWOOFER into an appropri- ate socket.

SUBWOOFER

IN

8

9

Page 5
Image 5
Samsung MAXDL44RH/XEF manual Rear Panel View, Where to Install Your Mini-Compact System, Connecting the Loudspeakers