Where to Install Your

Mini-Compact System

To take full advantage of your new mini-compact system, fol- low these installation instructions before connecting the unit.

Install the system on a flat, stable surface.

Never place this unit on carpeting.

Never place this unit in an outdoor area.

Maintain an open space of approximately 6 inches (15 cm) on the sides and rear of the system, for ventilation purposes.

Make sure that you have enough room to open the compact disc compartment easily.

Place the loudspeakers at a reasonable distance on either side of the system to ensure good stereo sound.

Direct the loudspeakers towards the listening area.

For optimum performance, make sure that both speakers are placed at an equal distance above the floor.

 

 

 

 

 

 

Disc1

Disc2

Open/Close

 

 

 

 

 

 

Disc3

Disc Change

 

 

 

 

 

 

 

Dolby

Power

 

On/Standby

Demo

 

 

 

 

Surround

Sound

 

 

Timer/

 

 

 

 

 

 

 

 

Clock

 

 

 

 

DSP/EQ

S.Bass

 

 

 

 

 

 

 

 

 

Display

 

 

 

 

 

 

 

 

 

R

Band

 

 

Dolby Digital

 

 

 

 

 

 

 

 

 

RDS

 

 

 

 

 

 

 

 

PTY

 

TUNER

DVD/CD

TAPE

AUX

Volume

 

 

Mono/ST.

Down

Tuning Mode

Up

 

Multi Jog

 

 

 

Display

 

 

 

 

 

 

 

 

 

Counter

Memory

REV.Mode

 

 

 

 

 

 

Reset

 

 

 

 

 

Enter

 

 

 

 

 

 

 

 

 

Deck 1/2

Dubbing

 

 

 

 

Phones

 

 

 

 

 

 

 

 

 

 

 

Normal

High

 

 

 

 

 

 

CD Synchro

REC/Pause

Record Lock

 

 

 

 

Connecting your System to the Power Supply

The main lead must be plugged into an appropriate socket.

Before plugging your system into a main socket, you must check the voltage.

1

Plug the main lead (marked AC Cord on the rear of the system) into

 

an appropriate socket.

2

Press the On/Standby button to switch your mini-compact system

 

on.

 

 

R

F

 

SP

Inserting Remote Control Batteries

GB

Insert or replace remote control batteries when you:

Purchase the mini-compact system

Find that the remote control is no longer operating correctly

When replacing the batteries, use a new set of batteries and never mix alkaline and manganese batteries.

1 Place your thumb on the position marked on the battery compart- ment cover (rear of the remote control) and push the cover in the direction of the arrow.

2 Insert two AAA, LR03 or equivalent batteries, taking care to respect the polarities:

+ on the battery against + in the battery compartment.

on the battery against – in the battery compartment.

3 Replace the cover by sliding it back until it clicks into position.

Video Output Selection

Press the Dolby Surround button in POWER OFF, then it is converted to

NTSC PAL ” and select the TYPE you want.

Example : Select PAL, if TV is for PAL.

When disk is set to NTSC in PAL, it doesn't operate.

 

 

 

 

 

 

Disc1

Disc2

Open/Close

 

 

 

 

 

 

Disc3

Disc Change

 

 

 

 

 

 

 

Dolby

Power

 

On/Standby

Demo

 

 

 

 

Surround

Sound

 

 

 

 

 

 

 

 

 

Timer/

 

 

 

 

 

 

 

 

Clock

 

 

 

 

DSP/EQ

S.Bass

 

 

 

 

 

 

 

 

 

Display

 

Band

 

 

 

 

 

 

 

R

 

 

Dolby Digital

 

 

 

 

 

 

 

 

 

RDS

 

 

 

 

 

 

 

 

PTY

 

TUNER

DVD/CD

TAPE

AUX

Volume

 

 

 

 

 

 

Mono/ST.

Down

Tuning Mode

Up

 

Multi Jog

 

 

 

Display

 

 

 

 

 

 

 

 

 

Counter

Memory

REV.Mode

 

 

 

 

 

 

Reset

 

 

 

 

 

Enter

 

 

 

 

 

 

 

 

 

Deck 1/2

Dubbing

 

 

 

 

Phones

 

 

 

 

 

 

 

 

 

 

 

Normal

High

 

 

 

 

 

 

CD Synchro

REC/Pause

Record Lock

 

 

 

 

7

Page 7
Image 7
Samsung MAXDN87RH/ELS, MAXDN83RH/ELS manual Video Output Selection, Where to Install Your Mini-Compact System