Setting the Clock Automatically
9Press the ENTER button.
Press the ▲ or ▼ button to select On or Off, then the ENTER button. The message Select the time zone where you are located. is displayed.
10Press the ▲ or ▼ button to highlight the time zone for your local area. Press the ENTER button.
If clock is not automatically set, see pages 18~19 to set the clock.
11The message Enjoy your watching. is displayed. When you have finished, press the ENTER button.
➢Even if the ENTER button is not pressed, the message will automatically disappear after several seconds.
If you want to reset this feature...
1Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the ENTER button.
2Press the ENTER button to select Plug & Play.
For further details on setting up options, refer to the page 10. ➢ The Plug & Play feature is only available in the TV mode.
Plug & Play |
| |
Set to daylight saving time. |
| |
DST | Off |
|
| On |
|
Move | Enter | Skip |
Plug & Play |
| |
Select the time zone where you are located. | ||
Newfoundland |
|
|
Atlantic |
|
|
Eastern |
|
|
Central |
|
|
Mountain |
|
|
Pacific |
|
|
Alaska |
|
|
Hawaii |
|
|
Move | Enter | Skip |
Enjoy your watching. |
| |
| OK |
|
Memorizing the Channels
Your TV can memorize and store all of the available channels for both air and cable channels. After the available channels are memorized, use the CH 
and CH 
button to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels(automatic) and adding or deleting channels(manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV(i.e. an air or a cable system).
1Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
2Press the ENTER button select Antenna.
Press the ▲ or ▼ button to select Air or Cable, then press the ENTER button.
Storing Channels in Memory (Automatic Method)
3Press the ▲ or ▼ button to select Auto Program, then press the ENTER button.
4 Press the ▲ or ▼ button to select the antenna connection, then press the ENTER button. ➢ Air: “Air” antenna signal.
Cable: “Cable” antenna signal.
Air+Cable: “Air” and “Cable” antenna signals. ➢ If you selected “Air”, then go to step 7.
5 Press the ▲ or ▼ button to select Cable, then press the ENTER button. The cable system menu is displayed .
6Press the ◄ button, then the ▲ or ▼ button to select the cable system for analog and digital channels respectively. Press the ► button to select Start, then press the ENTER button.
➢If you have Digital cable, select the signal source for both Analog and Digital.
➢STD, HRC, and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected.
7After all the available channels are stored, the Auto Program menu reappears.
You can also press the AUTO PROG. button on the remote control to bring up the Auto Program menu.
| Channel | ||
Antenna |
| : Air | |
Auto Program |
| Cable | |
Clear Scrambled Channel | |||
Channel List |
|
| |
Name |
|
|
|
Fine Tune |
|
| |
Signal Strength |
|
| |
Move | Enter | Return | |
| Auto Program | ||
Selects the antenna to execute the Auto | |||
Program function. |
|
| |
Air |
|
| Start |
Cable |
|
| Start |
Air + Cable |
| Start | |
Move | Enter | Return | |
| Auto Program | ||
Selects a cable signal type for your | |||
location. | Analog |
|
|
STD |
| Start | |
|
| ||
HRC |
|
|
|
IRC | Digital |
|
|
STD |
|
| |
|
|
| |
HRC |
|
|
|
IRC |
|
|
|
Move | Enter | Return | |
Auto Program |
| ||
Auto Program in Progress. |
| Air 16 | |
|
|
| 15% |
| Stop |
|
|
| Enter | Return | |
English - 11
