Manuals / Brands / Photography / Digital Camera / Sanyo / Photography / Digital Camera

Sanyo VPC SX 560, VPC-SX560E, VPC-SX560EX VG +, VG –, – 20 –, ± 0.1Vp-p, ± 0.3 Vp-p, ± 0.05 Vp-p, ± 0.05 Vp-p, (VG) waveform, CL173 waveform, CL173 waveform, CL173 waveform, CL171 waveform

1 33

Download 33 pages, 595.07 Kb

10-2. LCD RGB Offset Adjustment

Adjusting method:

1.Adjust LCD “RGB offset” so that the amplitude of the CL173 waveform is 7.3 V ± 0.3 Vp-p.

7.3 V

± 0.3 Vp-pCL173 waveform10-3. LCD Gain Adjustment

Adjusting method:

1.Adjust LCD “Gain” so that the amplitude of the CL173 wave- form is 4.0 V ± 0.1 Vp-p.

Note:

10-2. LCD RGB Offset adjustment should always be carried out first.

4.0 V

± 0.1Vp-p

CL173 waveform

10-4. LCD Blue Brightness Adjustment

Adjusting method:

1. Adjust LCD “B Bright” so that the amplitude of the CL171 waveform is VG + 0.2 ± 0.05 Vp-p with respect to the CL173 (VG) waveform.

Note:

10-2. LCD RGB Offset adjustment and 10-3. LCD Gain adjustment should always be carried out first.

VG

CL173 waveform

VG + 0.2± 0.05 Vp-pCL171 waveform10-5. LCD Red Brightness Adjustment

Adjusting method:

1.Adjust LCD “R Bright” so that the amplitude of the CL172 waveform is VG – 0.1 ± 0.05 Vp-p with respect to the CL173

(VG) waveform.

Note:

10-2. LCD RGB Offset adjustment and 10-3. LCD Gain adjustment should always be carried out first.

VG

CL173 waveform

VG – 0.1

± 0.05 Vp-p

CL172 waveform

– 20 –

Contents

(Product Code : 126 279 01) (Europe) (PAL Genenral) (Product Code : 126 279 03) PRODUCT SAFETY NOTICE REFERENCE No. SM5310249 1-1.CA1 CIRCUIT DESCRIPTION Around CCD block Input SHT Buffer XSHT XSG3B 5. Transfer of Electric Charge by the Horizontal CCD The transfer system for the horizontal CCD emplays a 2-phasedrive method (1) (2) (3) 1-2.CA2 CIRCUIT DESCRIPTION 3. LCD Block SVRAM – 6 – 1-3.CA3 CIRCUIT DESCRIPTION 1-4.PW1 POWER CIRCUIT DESCRIPTION 1-5.PW1 STROBE CIRCUIT DESCRIPTION 1-6.SY1 CIRCUIT DESCRIPTION 2. Internal Communication Bus Fig. 4-1Internal Bus Communication System 3. Key Operaiton Table 4-2.Key Operation 4. Power Supply Control Table 4-3.Camera Mode (Battery Operation) 6. Speaker 2-3.REMOVAL OF HOLDER BATTERY AND PW1 BOARD 4. Holder battery 3. Remove the solders 2. Two screws 5. Three screws 4. Two screws 2. Two screws 5. Two connectors 1. Three screws 3. Lens VF 3. ELECTRICAL ADJUSTMENT 3-1.Table for Servicing Tools Ref. No Name Part code 3-5.Connecting the camera to the computer To serial port or USB port Serial cable USB cable AC adaptor 3-6.Adjust Specifications [PW1 board (Side B)] Note: Preparation: 1. IC501 Oscillation Frequency Adjustment 8. Lens Adjustment Adjustment condition: 9.CCD Defect Detect Adjustment 10. LCD Panel Adjustment [CA3 board (Side A)] 10-2.LCD RGB Offset Adjustment Adjust LCD “RGB offset” so that the amplitude of the CL173 waveform is 7.3 ± 0.3 Vp-p CL173 waveform 10-3.LCD Gain Adjustment 4. USB STORAGE INFORMATION REGISTRATION 5. TROUBLESHOOTING GUIDE POWER LOSS INOPERTIVE OFF NORMAL YES N.S.P.: Not available as service parts LOCATIONPARTS NO. DESCRIPTION ELECTRICAL PARTS Materials of Capacitors and Resistors are abbreviated as follows ; Resistors Capacitors MT-FILM COMPL PWB,CA-2 PARTS NO (CRYSTAL DEVICES) (INDUCTORS) (MISCELLANEOUS) COMPL PWB,CA-3 (VARIABLE RESISTOR) COMPL PWB,PW-1 (VARIABLE RESISTORS) (TRANSFORMERS) (JACK) COMPL PWB,SY-1 (INDUCTOR) (SWITCHES) SANYO Electric Co.,Ltd. Osaka, Japan