Disc Drive
Installation Guide
Cheetah
ST136403LW/LC
Contents
Preface
Handling precautions
Electrostatic discharge protection
Always handle the drive by its edges or frame
Important safety information and precautions
Always observe the following warnings and precautions
Wichtige Sicherheitshinweise
Page
chädigung der Komponenten und Erlöschen des Garantieanspruchs führen
Regulatory agency compliance
Electromagnetic susceptibility
Electromagnetic compliance
Electromagnetic compliance for the European Union
Australian C-Tick
General description
Figure 1. Cheetah 36 family drive LW model shown
Single-ended and low voltage differential modes
The primary benefits of LVD technology
SE and LVD bus configurations
Data bus widths
Providing adequate cooling
Kühlung des Systems
Above unit Under unit
Figure 2. Suggested air flow
Abbildung 2. Empfohlener Luftstromverlauf
Above unit Under unit
Characteristics
ST136403LW/LC
Asynchronous data transfer rate
Low voltage
DC power requirements ±5%1 +5
LVD mode
Single-ended SE
How to install the drive
LW model installation
1. Set the SCSI ID on the drive
Figure 3. Setting the SCSI ID on LW model drives
Drive Front
2. Configure termination
Figure 4. SCSI bus termination
Cheetah 36 Installation Guide, Rev. A
3. Configure termination power
Figure 5. Setting terminator power jumpers
Note On some LEDs the flat side of indicator is cathode
Figure 6. Drive Active LED indicator connections
4. Connect the drive activity remote LED optional
Reserved Activity LED Reserved
Write Protect option
Single-ended mode option
Delay Motor Start and Motor Start options
Parity Check option
Figure 7. Additional jumper options
R R S D M W P E E T E S E P D S S P
Pin Pin
6. Mount the drive in the host system and connect cabling
7. Format the drive
Figure 8. Connecting cables to the drive
Cheetah 36 Installation Guide, Rev. A
Figure 9. Multiple-drive connection to host adapter
1 “X” means up to 15 devices on the SCSI bus
Figure 10. Mounting configuration dimensions LW model
Dimension Table
Additional connector on LW model drives
Figure 11. Alternate SCSI ID select and LED connection
LC model installation
1. Set the SCSI ID on the drive
Figure 12. Setting the SCSI ID on LC model drives
Cheetah 36 Installation Guide, Rev. A
Drive Front
2. Configure termination
LC model drives are designed for installation in host sys- tems that have a backplane with single connector attach- ment SCA connections. Termination is normally provided on this backplane. Check your host system documentation for details
Write Protect option
Single-ended mode option
Delay Motor Start and Motor Start options
Parity Check option
Figure 13. Additional jumper options
Cheetah 36 Installation Guide, Rev. A
4. Mount the drive in the host system
Figure 14. 80-pin I/O connection to drive LC model
80-pin SCSI I/O Connector Pin J2 J6
Figure 15. Mounting configuration dimensions LC model
Dimension Table
Max screw penetration into side of drive
5. Format the drive
Important information about formatting the drive
DOS, Windows 3.1, Windows 95, and Windows
System preparation
Drive partitioning
Drive formatting
Macintosh
Automated Services
Seagate Technology support services
Online Services
Internet
Presales Support
Technical Support
Seagate Express
Warranty Repair
Customer Service CSO
USA/Canada/Latin America Support Services
Authorized Service Centers
MA Informatica
European Support Services
Call Center
Memofix
Fax Services-All European Countries
Africa/Middle East Support Services
Asia/Pacific East Support Services
SeaBOARD
SeaFAX
Warranty Repair
FAX +81-3-5462-2979
Page
Page
Page
Publication Number 83329450, Rev. A, Printed in USA
Seagate Technology, Inc
920 Disc Drive, Scotts Valley, CA 95066-4544, USA
