Manuals / Seagate / Computer Equipment / Computer Drive

Seagate ST136403LW/LC manual

Models: ST136403LW/LC

1 52

Download 52 pages 47.61 Kb

Page 51

Image 51

Seagate ST136403LW/LC manual

Contents

ST136403LW/LC Installation GuideCheetah Disc DriveContents Preface Handling precautions Electrostatic discharge protectionAlways handle the drive by its edges or frame Important safety information and precautions Always observe the following warnings and precautions Wichtige Sicherheitshinweise Page chädigung der Komponenten und Erlöschen des Garantieanspruchs führen Regulatory agency compliance Electromagnetic susceptibilityElectromagnetic compliance Australian C-Tick Electromagnetic compliance for the European UnionFigure 1. Cheetah 36 family drive LW model shown General descriptionThe primary benefits of LVD technology Single-ended and low voltage differential modesSE and LVD bus configurations Data bus widthsProviding adequate cooling Kühlung des Systems Above unit Under unit Figure 2. Suggested air flowAbbildung 2. Empfohlener Luftstromverlauf Above unit Under unitCharacteristics ST136403LW/LCAsynchronous data transfer rate Single-ended SE DC power requirements ±5%1 +5LVD mode Low voltageHow to install the drive LW model installation1. Set the SCSI ID on the drive Drive Front Figure 3. Setting the SCSI ID on LW model drives2. Configure termination Cheetah 36 Installation Guide, Rev. A Figure 4. SCSI bus terminationFigure 5. Setting terminator power jumpers 3. Configure termination powerReserved Activity LED Reserved Figure 6. Drive Active LED indicator connections4. Connect the drive activity remote LED optional Note On some LEDs the flat side of indicator is cathodeParity Check option Single-ended mode optionDelay Motor Start and Motor Start options Write Protect optionFigure 7. Additional jumper options R R S D M W P E E T E S E P D S S PPin Pin 7. Format the drive 6. Mount the drive in the host system and connect cablingCheetah 36 Installation Guide, Rev. A Figure 8. Connecting cables to the drive1 “X” means up to 15 devices on the SCSI bus Figure 9. Multiple-drive connection to host adapterDimension Table Figure 10. Mounting configuration dimensions LW modelFigure 11. Alternate SCSI ID select and LED connection Additional connector on LW model drives1. Set the SCSI ID on the drive LC model installationFigure 12. Setting the SCSI ID on LC model drives Cheetah 36 Installation Guide, Rev. ADrive Front LC model drives are designed for installation in host sys- tems that have a backplane with single connector attach- ment SCA connections. Termination is normally provided on this backplane. Check your host system documentation for details 2. Configure terminationParity Check option Single-ended mode optionDelay Motor Start and Motor Start options Write Protect optionCheetah 36 Installation Guide, Rev. A Figure 13. Additional jumper options4. Mount the drive in the host system Figure 14. 80-pin I/O connection to drive LC model80-pin SCSI I/O Connector Pin J2 J6 Figure 15. Mounting configuration dimensions LC model Dimension TableMax screw penetration into side of drive Important information about formatting the drive 5. Format the driveDOS, Windows 3.1, Windows 95, and Windows System preparationDrive partitioning Drive formatting Macintosh Internet Seagate Technology support servicesOnline Services Automated ServicesPresales Support Technical SupportSeagate Express Authorized Service Centers Customer Service CSOUSA/Canada/Latin America Support Services Warranty RepairMemofix European Support ServicesCall Center MA InformaticaSeaBOARD Africa/Middle East Support ServicesAsia/Pacific East Support Services Fax Services-All European CountriesSeaFAX Warranty RepairFAX +81-3-5462-2979 Page Page Page Publication Number 83329450, Rev. A, Printed in USA Seagate Technology, Inc920 Disc Drive, Scotts Valley, CA 95066-4544, USA