Manuals / Seagate / Computer Equipment / Computer Drive

Seagate ST136403LW/LC manual Electromagnetic compliance for the European Union, Australian C-Tick

Models: ST136403LW/LC

1 52

Download 52 pages 47.61 Kb

Page 11

Cheetah 36 Installation Guide, Rev. A

9

Electromagnetic compliance for the European Union

If this model has the CE Marking it complies with the European Union requirements of the Electromagnetic Compatibility Direc- tive 89/336/EEC of 03 May 1989 as amended by Directive 92/31/ EEC of 28 April 1992 and Directive 93/68/EEC of 22 July 1993.

Australian C-Tick

If this model has the C-Tick Marking it complies with the Austra- lia/New Zealand Standard AS/NZS3548 1995 and meets the Electromagnetic Compatibility (EMC) Framework requirements of Australia’s Spectrum Management Agency (SMA).

Image 11

Seagate ST136403LW/LC manual Electromagnetic compliance for the European Union, Australian C-Tick

Contents

ST136403LW/LC Installation GuideCheetah Disc DriveContents Preface Always handle the drive by its edges or frame Handling precautionsElectrostatic discharge protection Important safety information and precautions Always observe the following warnings and precautions Wichtige Sicherheitshinweise Page chädigung der Komponenten und Erlöschen des Garantieanspruchs führen Electromagnetic compliance Regulatory agency complianceElectromagnetic susceptibility Australian C-Tick Electromagnetic compliance for the European UnionFigure 1. Cheetah 36 family drive LW model shown General descriptionThe primary benefits of LVD technology Single-ended and low voltage differential modesProviding adequate cooling SE and LVD bus configurationsData bus widths Kühlung des Systems Above unit Under unit Figure 2. Suggested air flowAbbildung 2. Empfohlener Luftstromverlauf Above unit Under unitAsynchronous data transfer rate CharacteristicsST136403LW/LC Single-ended SE DC power requirements ±5%1 +5LVD mode Low voltage1. Set the SCSI ID on the drive How to install the driveLW model installation Drive Front Figure 3. Setting the SCSI ID on LW model drives2. Configure termination Cheetah 36 Installation Guide, Rev. A Figure 4. SCSI bus terminationFigure 5. Setting terminator power jumpers 3. Configure termination powerReserved Activity LED Reserved Figure 6. Drive Active LED indicator connections4. Connect the drive activity remote LED optional Note On some LEDs the flat side of indicator is cathodeParity Check option Single-ended mode optionDelay Motor Start and Motor Start options Write Protect optionPin Pin Figure 7. Additional jumper optionsR R S D M W P E E T E S E P D S S P 7. Format the drive 6. Mount the drive in the host system and connect cablingCheetah 36 Installation Guide, Rev. A Figure 8. Connecting cables to the drive1 “X” means up to 15 devices on the SCSI bus Figure 9. Multiple-drive connection to host adapterDimension Table Figure 10. Mounting configuration dimensions LW modelFigure 11. Alternate SCSI ID select and LED connection Additional connector on LW model drives1. Set the SCSI ID on the drive LC model installationDrive Front Figure 12. Setting the SCSI ID on LC model drivesCheetah 36 Installation Guide, Rev. A LC model drives are designed for installation in host sys- tems that have a backplane with single connector attach- ment SCA connections. Termination is normally provided on this backplane. Check your host system documentation for details 2. Configure terminationParity Check option Single-ended mode optionDelay Motor Start and Motor Start options Write Protect optionCheetah 36 Installation Guide, Rev. A Figure 13. Additional jumper options80-pin SCSI I/O Connector Pin J2 J6 4. Mount the drive in the host systemFigure 14. 80-pin I/O connection to drive LC model Max screw penetration into side of drive Figure 15. Mounting configuration dimensions LC modelDimension Table Important information about formatting the drive 5. Format the driveDrive partitioning DOS, Windows 3.1, Windows 95, and WindowsSystem preparation Drive formatting Macintosh Internet Seagate Technology support servicesOnline Services Automated ServicesSeagate Express Presales SupportTechnical Support Authorized Service Centers Customer Service CSOUSA/Canada/Latin America Support Services Warranty RepairMemofix European Support ServicesCall Center MA InformaticaSeaBOARD Africa/Middle East Support ServicesAsia/Pacific East Support Services Fax Services-All European CountriesFAX +81-3-5462-2979 SeaFAXWarranty Repair Page Page Page 920 Disc Drive, Scotts Valley, CA 95066-4544, USA Publication Number 83329450, Rev. A, Printed in USASeagate Technology, Inc